World Chemical Pump

Hot Products

Self-priming Chemical Pump

Wear-resisting passage Pump

Chemical Submerged Pump

Can Motor Chemical Pump

Twin Screw Pump

Chemical Passage Pump

Horizontal High Speed Pump

Ventical Condensate Pump

Portable electric barrel pump

High Pressure Horizontal Multistage Pump

FAQ

SUZUKI motorcycle oil pump is not on the oil, the oil circuit is not blocked, to replace the oil pump, or pump is not on the oil

Is the oil filter and the oil filter plugged? Is the filter core apron missing? How do you make sure there's no blockage? No reason for the oil is only the oil pump damage, filter, filter or oil clogged, lack of oil and several other reasons.

My motorcycle has been running for a long time. Now, about 2 bottles of motor oil in one hundred kilometers are too expensive. Can you add the engine oil to the mailbox according to the approximate proportion? Thank you.

You'd better not put it in the tank. Will affect the gasoline combustion, because the oil concentration and gasoline is not the same. And the functions are different. What is the place with what place, with a little or no big problem, but the exhaust pipe will take the blue smoke, the damage to the engine is not great. If so, I suggest going to the 4S shop to take down the tank and clean it.The oil is added to the tank, depending on the type of oil (burning or lubricating oil) and the amount added. If it's the engine oil that has minimal impact on the engine, the mixing ratio should be within 1:25.If the amount of oil added to the tank is more than 1:25, the possibility of carbon deposition in the cylinder head of the engine will increase. Below this value can be assured to use, the smaller the proportion, the smaller the impact on the engine.

What about the oil leakage of automobile oil pump?

If the oil pump is broken, replace it, if it is a rubber pad, change the cushion.An oil pump in a lubricating system that forces the oil from the oil pan to the engine moving parts. Used to increase the pressure of the oil and to ensure a certain amount of oil.

Reasons for heating of oil pump in roadheader

If you are using a high temperature oil pump motor may be caused by the following reasons: first, check whether the pump because of overload caused by fever; test method: with a twist of the hand to see if high temperature pump connector flexible operation, such as flexible and can be excluded: Two: check to see how the materials proportion is too large. If too much can cause motor overheating; Troubleshooting: re selection; three: when the working pressure is too large can cause motor overheating and Troubleshooting: can try to use high gear pump should be able to solve the problem of pressure; four: use range (flow head) over high temperature oil pump design requirements? Choose the right motor according to the serial type. Five: high temperature oil pump motor assembly and coaxial pump motor will not only of fever and noise during use will increase, solution: open angle screw, re check coaxiality, and then tighten the screws can be solved;

Where is the oil pump installed?

When installing the engine oil pump, after the engine is refitted. When installed, the first crank, the first cylinder piston at TDC position, then pump filled with oil (don't forget), the oil outlet groove direction of pump shaft installed electric drive shaft plug towards the pump, when the oil into the engine body, recesses in parallel with the axis of the crankshaft.Effect of lubricating oil pump system within pump: pump is the engine oil level to a certain pressure, forced to pressure parts of the engine on the surface of the movement. The structure of oil pump can be divided into two types: gear type and rotor type. Gear type oil pump is divided into internal gear type and external gear wheel type, generally referred to as gear pump.Used to increase the pressure of the oil and to ensure a certain amount of oil,Oil pumpForced to the surface friction of oil components. The internal combustion engine is widely used in gear and rotor pump. The gear type oil pump has the advantages of simple structure, easy processing, reliable work, long service life, high pressure oil pump, rotor pump rotor is widely used for complex shape by powder metallurgy pressing. This pump has the advantages of gear pump is the same however, the advantages of compact structure, small volume.

What is the oil pump on the car? If it is blocked, how can I solve it?

Providing lubricating oil and lubricating pressure for each friction pair of the engine

When the oil is removed from the oil pump, enter the oil filter, and the oil runs towards it Specific point (I also know to lubrication). That's where it goes, where it goes, where it goes and where it goes back Are they all through the oil (Road) pipe?

Let me add, the larger engine oil pump - the cooler - the main oil road - to the other oil ducts

What is the function of the oil pump?

Keep the oil pressure down and keep the oil circulating while the engine is running