The pump is a centrifugal pump of horizontal,axial end suction and radial discharge design. This is a universal structure of chemical process pump used internationally.
- Q:Bending machine, oil pump motor abnormal sound, what's the matter?
- First, the hydraulic oil is not enough, will cause abnormal sound of the pump, check the amount of oil enough;Two, hydraulic oil dirty plug, oil suction port filter will cause abnormal sound, and oil cylinder, motor and other components of the work is not easy, in this case, wash the filter, and filter hydraulic oil or replace hydraulic oil;Three, the pump is damaged, the inner surface of the stator vane pump will wear a different sound, internal plunger piston pump will damage the abnormal noises and vibration of hydraulic system badly, the stress of this situation would not be stable, may be due to a hard object inside the hydraulic oil in the pump caused by card;Basically, these three situations.
- Q:The function of the oil pump screen is troublesome
- Hello, just filter the oil and the dirt in it
- Q:GY6 engine oil pump installation direction, there is an arrow pointing to the other side of the ah
- The direction of the arrow indicates the direction of the oil, and the one with the arrow is connected to the engine oil inlet.
- Q:How to judge the Audi a6l2.0t oil pump broken?
- If not removed, the amount of oil on the car, low oil pressure on the problem, if removed, go round to see how the pumping effect
- Q:What is the effect of excessive oil on the oil pump?
- Too much oil, will increase the rotational resistance of the crankshaft, reduce the output power of the engine, and the excess oil from entering the combustion chamber in the combustion, burning oil, causing the vehicle to take the blue smoke, and increased fuel consumption, oil residue after combustion (the main component is carbon, very hard) will accumulate in the combustion chamber wall. To reduce the space of the combustion chamber, thereby reducing the engine compression ratio, at the same time, will accelerate the wear of cylinder and piston so as to reduce the service life of the vehicle.
- Q:What's the use of an oil pump in an automobile engine?
- When the engine is transported within pump oil lubrication parts inside the engine.
- Q:What are the fuel pump inspection items for diesel generator sets?
- The 1. check valve plane if worn, sag, such as pitting phenomenon, application of grinding paste on the plate grinding, severe cases should be renewed.2. of the one-way valve seat surface wear serious or not smooth, should be replaced.3., the top rod and the top sleeve wear seriously, so that the gap increases, the seal becomes worse, the diesel oil leak seriously, then need to replace with the shell, or choose the enlarged size of the top pole, but need to pass the mutual research.The coarse strainer core 4. oil inlet pipe joint, and easy to be cottony sundries plug, effect of fuel supply, it should always pay attention to the clean fuel and remove the dirt on the filter core.5. hand oil pump piston rubber ring damaged, should be replaced in good time. After the center of gravity of the oil pump is assembled, the moving parts of the piston, the ejector rod and the other parts of the oil pump are required to be in good motion during the whole journey, and no blocking and blocking are allowed. The hand pump should be light and flexible. Pay attention to the installation of the one-way valve spring. The check valve spring must be accurately embedded in the spring slot.
- Q:How to dismantle the oil pump chain saw
- Komatsu? 4500.5200.5800, because the clutch is anti wire, you can only use the son rushed out of iron bell. As soon as you clutch, you'll see.
- Q:The motorcycle oil pump is broken. Can the oil be added directly to the tank?
- Motorcycle oil pump broken, oil can not be directly added to the tank.If the proportion of 40:1 in gasoline engine oil, that's not what relationship, does not affect the use, if down a lot, recommend cleaning oil, because the oil will cause the combustion of coke, when the cleaning nozzle is 200 if ovo, higher proportion, even fire are not, ultimately only cleaning.
- Q:The car burning oil pump replacement must do
- 1, there are many reasons, but also models (steam, firewood) and so on.2, long-term use of poor quality oil, or viscosity grade unqualified engine oil and other internal wear too large.3, under normal circumstances, the engine will burn some of the oil from the cylinder block, piston and valve lubrication, consumption within the relevant provisions of the national standard range for normal (GB/T19055), and vice versa. The lowest scale car burning oil is often accompanied by smoke or in a maintenance period is lower than the oil gauge oil level.4, long time does not change oil or too long delay, not timely maintenance; piston and piston ring due to the use of long, normal wear, or abnormal wear and tear caused by the gap is too large.5, in addition, there are valve seals, crankcase forced ventilation, PCV valve damage, congestion, oil pump pressure, or its own failure can also be caused.There are many reasons why, as you describe the content is not detailed, the temporary analysis so far.
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average