Hot oil pump has been widely applied in the perolene heating system in China, which can be found in such industrial field as petroleum, chemical engineering, rubber, plastic, pharmacy, texiles, pringting and dyeing, road building and food.
- Q:The oil pump is greased by hand, so why not oil it on the truck?
- Hello. Check the line for pressure reliefNormal. Is there any deformation of the oil pan?. Lead to less oil in the oil pump strainer and air. That's why I don't use oilBe sure to check if the oil pan is deformed or notAfter loading, the oil pan is not installed. Put the oil into the oil with the screen below. Move the car to see if there is any oil or pressure relief
- Q:When the car runs neutral, does the oil pump work?
- The main reason for the car's neutral sliding is the safety factor! The problem is not the oil pump or the AT transmission oil, of course, those are incidental.Free sliding emergency brake wheel by the brake caliper, without engine braking effect, four tire deceleration unbalanced if it is easy to slip occurred even rollover accident, especially on the ground part of water or ice is more dangerous. Furthermore, when the engine is neutral, the engine is in idle speed, and the fuel consumption is higher when the engine is in partial load than in the idle state! If the maximum fuel consumption of the engine is 100%, the idle fuel consumption is at least 75% of that level. Do you think there is any point in the neutral taxi? On the contrary, with gear stalls, the appropriate time to step on the clutch, not only can use the engine brake balance brake force, but also can be reduced to a very low speed, reduce fuel consumption, a variety of benefits, but also safe...Of course, some of the teachers still believe in neutral skating. They may have learned from their master. They may have been written down from the inner consciousness, but they may not always be right.Automatic transmission cars do not speed upstairs said more than 60 neutral is the reason, in fact the basic automatic shift not to hang N files, more than 1min parking with P files, N files for hydraulic torque converter is still working, is not good for the life of the transmission. If a mechanical clutch is used instead of a hydraulic torque converter to connect the flywheel and transmission to an automatic transmission, such as a double clutch gearbox, there is no gap.
- Q:JMC 462Q engine does not go to the cylinder head, where is the oil pump located?
- You can't fix it by yourself.1, remove the valve compartment cover, you can see the rocker shaft, loosen the top of the middle fixed screws.2 you can blow it up in a high pressure air pump, clear it up, start the engine, and spray the oil outward.3, also can use steel wire (about 50cm long, rough 1mm or so, can reach that hole), to dredge, must exceed 25mm (cylinder head height) just go.4 or more can not work, and finally only remove the cylinder head.The 5 reason is that the cylinder pad (oil hole) is blocked by carbon deposits, and the engine oil can not reach the rocker arm.
- Q:3000 Zhijun hydraulic top rattled, replaced the hydraulic top oil pump
- Estimation is steel roof deformation, shaft seal wear need to check and top steel pillar joints without oil
- Q:Does the abnormal oil pump affect power?
- Hello, oil pump damage will result in lower oil pressure, engine noise, and accelerate the wear and tear of the car to start the internal parts
- Q:What are the causes of motorcycle engine oil pump damage?
- The oil is bad and the oil is not changed regularly
- Q:Will it clog up the oil pump by cleaning the engine oil which is strong enough to clog up the oil circuit?
- If the engine is too much carbon deposits, the use of such properties of oil, it is true that such a situation can occur. The first is blocked by the oil pump filter. The oil passages are not blocked, because carbon deposits are filtered first by the filter. Sludge is capable of entering the oil passages.
- Q:In the 1 to 2 seconds when the vehicle is started, does the oil pump inject engine oil into the engine?
- Yes, the oil pump follows the crankshaft
- Q:TOYOTA oil pump not going off
- The problem is that the oil pump is broken or that the oil pressure relief valve is broken
- Q:What's the reason that I changed the new oil pump instead of the engine oil?
- When you switch the pump oil pump to oil or oil is that gambling is dead
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average