Q:If you put clay over wire and bake it would the wire melt and ruin the sculpture?Details on wire:I'm not sure what kind of wire it is but it says Bright Floral Wire..Wire is silverDetails on Clay:Again, im not sure what clay...its from polyform products and it says Premo Sculpey so im guessing Polymer? :#92;Clay is Black.Bakes for 275F (130C)30 minutes per/par/por1/4 in (6mm)

Copper Chicken Wire

Q:I have a 220v single phase kiln with two red wires labeled L1 and L2, and one white wire labeled N. It did not come with the plug, so I bought one and new wire 3/c 10awg, but it has ground(green), Hot(black), and neutral(White). I dont know how to proceed with wiring? any help would be great. Thanks. Jose

Wire L1 L2 to the spade looking terminals, and the n to the round pin.

Q:Ceiling fan has a black wire, white wire, green wire and also a black and white wire.

The black and white wire provides power to the lights; the black wire is to power the fan motor. If you have separate wall switches for lights and fan, you can control them separately. If there's a red wire in the box, connect it to the black and white fixture wire. The black goes to the black fan wire. The green is connected to the green screw on the fixture. All of the whites should be joined together. If you do not have separate wall switches for fan and lights, just join the black, black+white and black house wire together. You will then have to control the light with a pull cord.

Q:I am installing a GFCI outlet in the kitchen (20 AMP) the box that it is already installed in has more than nine wires running into it. What I need to know is how does one determine the load wires from line wires when there are multiple wires running to an outlet box?

Nine wires or nine cables? Nine wires is possible if there was a three-way switch in that box previously, or multiple outlets. Need to know what was in the box before. Pictures would also help.

Q:I just bought an aftermarket cd player for my Grand Cherokee and I would rather not have to cut and strip wires so I want to get an wiring harness adapter. My question is, can I just get any wiring harness adapter or do I need the direct connection adapter that is specifically made for Chrysler to Kenwood?

You just get the jeep wiring adapter and then solder or use crimp caps/butt-connectors to connect the wires to the aftermarket harness that comes with the aftermarket headunit. Also, depending on what year Jeep you have you may need an antenna adapter. AND I believe on the Jeeps (like the chryslers) there is not a usable ground wire in the factory wiring harness which means you will need to ground the aftermarket ground wire to the chassis via an existing bolt or drilling. Or, if the stock radio has one of these metal-mesh things affixed to the back, you can use that thing as well. But when you match up the Jeep harness you buy to the factory harness and you will be able to tell if there is ground wire in factory harness.

Q:wiring kit, subwoofers

by wiring kit do you mean the amps power kit? some of which will include speaker wire for the subs anyway usually your amp will come with instructions that tell you what the minimum gauge is the amp will accept for power, this is the gauge power and ground cable you will want to get maximum power to the amp and to prevent overheating issues, typically amps under 400 watts rms power will do fine with 8 gauge, amps 400-1000 rms will use 4 gauge and 1000+ will use 2/0 gauge wire, for the subwoofer speaker wire you can never go too big gauge only too small, a kicker 12 gauge speaker wire will work for almost any application

Q:is this a wire that like is the same as buying any other one?

8g might be a little overkill. A 10g 2 conductor wire should be sufficient for nearly any application. Here's a link with more than anyone ever needs to know about speaker wire:

Q:I heard that Japanese could load a low voltage without any wires in one direction for 1 meter! Of course 1 meter is nothing. But can we get rid of wires in next 50 or 100 years?

Losses are too high!

Q:Need ro know where to put the wires correctly

Most dryer outlets I have seen are labeled X Y G N Wire it this was and you will be good to go. X-This is for one of the hots, you can either put the red or black Y-Same as X G-This is the ground, usually bare copper. Make sure it is connected to the metal box where the outlet goes. N-Neutral, lets you have 120V for the motor, timer, and controls. This wire will be white. Just make sure the power is off before you start. Do the wires have to completely wrap around the screws.. If your talking about the outlet(the part with the 4 holes and you plug your dryer cable into) there are no screws to wrap around. You putg them in the slot and tighten the heck out of the screws. If it is something else get it as far around the screw as you can and make sure it goes on clockwise so the wire tightnes as you tightne the screw

Q:On what actually does ampere depends, thickness of wire or number of turns of wire or what else? Electrical

ampere depends on the number of turns..........