Q:Hi people! Our class is having a competition using 2 sheets of aluminum foil to design a boat and then, putting it in water to see how much pennies it can holdDo any of you know the best design for the boat so that it will hold the most pennies? Thanks,John Macdonald.

Electron Affinity Of Silicon

Q:Does anyone have a good beef brisket recipe for the grill?

Get under itThe wood is pushing outward perhaps? You didn't say where they were located Or put on a alunimum corner siding piece.

Q:We cannot find any really good beef jerky recipesCan anyone help?

3 lbs London Broil 2/3 C Worcestershire sauce 2/3 C of soy sauce 1 tspof black pepper 1 tspgarlic powder 1 tsponion powder 1 tspliquid smoke 2-3 tspTabasco Sauce 2-3 tspcrushed red peppers 2-3 tspsesame seeds MOP Mix all marinade ingredients together in a large (gallon size or larger) plastic zipper bagAdd sliced meat and refrigerate, turning and mixing every hour or twoHearty meats like beef and venison should be marinated overnight When ready to begin drying, place a sheet of aluminum foil on the bottom of the oven to aid in cleanupDrain meat in a colander and pat dry with paper towels (the drier the better at this point)Set oven at lowest temperature setting and carefully place meat slices directly onto oven racksLeave the oven door open a crack to allow moisture to escapeDrying times vary due to oven differences and meat sizePerfect jerky is firm and dry and not at all spongyHowever, if your jerky is so dry it breaks in two easily, it's probably over-dried Cooks Note: The recipe above is enough for about 3 pounds of meat, which will dehydrate down to about 16-18 ounces (Yow! Now you know why it's so expensive to buy Beef Jerky.) HOPE THIS HELPS! ENJOY!!!!!!!!!

Q:I have fiskers guillotine paper trimmer and I want to know how I can sharpen it I tried wax paper and aluminum with no luck.

well that depends on where you live in californiaThe brown insulation is most likely cellulose type insulationhow deep is it in your attic?wher i live it should be at least 12inches thick yes you can roll new insulation over it without taking the old out just use unfaced battsthis means rolled fiberglass insulation over the top with no paper facing on it and be sure to wear a face respirator and safety goggles

Q:i have an A5 but i want to know where can i get the power tube for itnothing cheap plzzz.

cut slits in the pork and stuff with garlic and spring onions salt and pepper and drizzle extra virgin olive oil over themseal tightly with foil and cook in oven on high heat for 10 - 15 mins and then turn the heat down to 225 and cook until done.

Q:I'm the only survivor on the islandi need to survive on the islandI have a few items that was with me when i got shipwrecked2 roll of toilet paper, candle wrapped in aluminum foilWhat can i do with these items to survive?What can i make of these items? Fruit Bats and geckoswhat they provide for me to survive? Answer quick receive 10 points

Maybe your confusing stainless steel with aluminum?

Q:Can i cook them in the microwaveHow do i do it? Best answer is first answer that tells me how to do it where it can be edible.

I would just do it all in one shot cause ventually when u force induct it you'll wanna go with more boost(everyone does it) and then your def gana need the rods.

Q:i have a 1991 350 chevy single cab step side 2wdlowering kit and 60 wide tires and eagle alloy chrome rimsi have just finished building a 350 short blockstandard 4in borei used the edelbrock rpm power package 202 aluminum heads and cami used the edelbrock tbi manifold with my stock tbiused an mallory dizzy and coil pack.aluminum rockersheaders wit flowmaster 44s true duals no catsalso a programmer that has been in the truck since i got iti am installing a 3000 stall torque converterauto trannyposi 3.73 gearsi am curious to know what it will run when i put everything togetherdoes anyone have an educated guess on 1/4 mile times? and predicted horsepower? all opinions are appreciated.

Once again I would like to of seen a credible sourceThe big problem with this natural gas question was weather the environmental standards were properly enforcedI hold this truth to be self evident that under George W Bush they were notAccording tot he source below there is a problem with the ground water in Wyoming but the EPA is trying to get three new regulations that would handle this.

Q:then released/dropped(1) Describe velocity changes (2) predict final magnitude of the velocity and show calculationsAt a certain point the velocity has supposedly reached its peak.I don't even know where to begin with this problem!

1) The block will accelerate downwards until the drag caused by the water becomes equal to the force from gravity minus the buoyancy caused by the displacement of water by the blockAt that point the velocity will remain constantWell constant until it either hits the bottom of the water or the water pressure becomes great enough to have a noticeable compression effect on the blockUnless this is a very very deep bit of water hitting the bottom is probably going to happen first2) The force pulling the mass down will be 1.3g the force pushing the mass up will be the bouyancy of the block, that is the mass of the volume of the water it displacesSo (1.3/density of Al) density of waterThe force resiting the blocks motion will be the drag from the water, as a first approximation this will be proportional to the blocks velocityFinal velocity will be where the forces balance so: 1.3g 1.3d(water)/d(Al) + kv where g 9.81m/s d(water) is the density of water (1 g/cm^3) d(Al) is the density of aluminum (2.70 g/cm^3) v is the final velocity of the block and k is the coefficient of drag for the blockv 1.3(g - d(water)/d(Al)) / k v 9.24/k k will be dependent on the shape of the block and surface finish and so is not possible to predict from the information given.