Submersible Water Pump QDX1.5-15-0.37
- Ref Price:
-
- Loading Port:
- Ningbo
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 5000 set/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Specifications
It's more compact,light on weight,easy for use.
It's suitable for home water supply,garden irrigation,building site,aquaculture
Application
Applying for building site ,hotel,restaurant,ship,mine,urban sewage,dejecta discharge,garden and farm irrigation, it also can be used for transporting liquid feed for fishing aquaculture and transporting dilute paper pulp.
Materials
· Pump body:Cast iron
· Motor housing:Aluminum
· Motor wire:Copper
· Impeller:Aluminum
· Mechanical seal:Ceramic&Graphite
· Shaft:45#steel
· Bearing:China
· Insulation class:B
· Protection class:IP68
Electrical Data
Rated power:0.37KW
Rated voltage:220/380V
Mains frequency:50/60Hz
Rated capacity:1.5m³ /h
Rated head:15m
Pipe size:25mm
- Q: Our house is situated on very sandy soil. I suspect that my water pump may be getting clogged with sand and silt and other debris. The water flow from the sinks and showers often stops randomly in the middle of the water running only to turn on maybe 30 seconds later. This seems to happen more and more frequently now where as a year ago and beyond it never occurred. Any suggestions?
- I would still be leaning towards alignment issues are at play here. What I would recommend is putting it on a dyno, not to check the power but so you can see what is happening while the engine is under a power load. I did build an engine once that could not keep belts on, they spun off. I have seen some truly strange things happen. Perhaps the strangest was a thrust bearing allowed to much crank shaft end play and as a result the starter was binding on the flywheel. Yet another was a cam shaft retainer not installed properly allowed the timing chain to snap. Another possibility is the crank damper pulley and not being seated properly.
- Q: okay i just put a new camshaft in my truck and before my water pump seemed to work but it leaked a little bit but my truck never got hot well i drove it a little bit after puting in the new camshaft and the top radiator hose and heater hose was warm but the bottom radiator hose was cold so i think my water pump went out but not to sure thanks to any answers
- when your water pump goes out, either it will leak from the weep holes which are the holes drilled in the pump by the manufacturer or around the pulley. If that is happening then its your pump. The other thing to check would be your thermostat, check this by turning your truck on and leaving the lid of the radiator. check the temperature of the water in the radiator with your finger if it warms up in ten minutes then its not your thermostat, if the water level goes down ( like lack of water) then its the pump.
- Q: when replacing the Water pump on an Isuzu rodeo while getting a new gasket does it require gasket sealant for this type of vehicle?
- it depends mainly on the gaskets you are using whether or not they are paper type gaskets or rubber type gaskets or cork type some cars have only sealant and no gaskets most rubber gaskets don't need sealant some install it anyway for extra protection but to much sealant it could clog your cooling system if they are paper type gaskets a little sealant is added protection some mechanics put sealant on the gasket simply to hold it in place during the install some gaskets require sealant and a specific one at that there are many different types of sealant keep in mind if your gasket manufacture requires sealants to install its would be listed on the box it arrives in for the pre installation guides make sure you get the one they say also all sealant that dry some are wet sealants and never dry, keep in mine that if the sealant requires dry time after install you follow those guide lines otherwise it will leak keep in mind also that the water pump housing bolts have a specific install and tightening and torque down for that type of gaskets like 15 foot pounds on the bolts for cork type gaskets if you crank the bolts down to tight its going to split the gaskets and your back to square one replacing it again
- Q: the pump is pumping hot wtaer from the hot water tank around the domestic hot water system, i.e to taps and shower.
- Depends on the type of pump, but for your garden variety type pump, there is a impeller of some sort that is turned by the motor to pump the water. The actual shaft of the motor is not in contact with the water (except where the impeller is attached to the shaft). A common type of failure mode here is when the seals on the shaft (which keep the water contained to the impeller area) have failed and water has gotten past the shaft seal and degraded the bearings holding the shaft = seizing up.
- Q: i installed a new pump don't know how to increase water pressure and to what what pressure it should be set
- This is very simple i would sugest the pressure to be set betwene 60 to 70 NO MORE THAN 70. 1. turn off power to pump (ether the circut breaker or a switch near the pressure switch) you dont want to weld the wrench to the switch. 2. remove the cover to the pressure switch its self (usly one #2 phillips screw) 3. now you will see 4 wires under some sloted screws nearest to the front of the switch, behint that is 1 or 2 bolts with a spring and a nut. 4. if you see 2 bolts you will want to turn the nut on the larger one to the right. you will want to tighten it about 1 to 2 full turns. (the same goes if there is only one bolt also) 5. now open the valve that is on the tank untill you here the switch click. then close the valve. 6. turn the power back on tio the pump and watch the pressure gauge on the tank. i DO NOT RECOMEND MORE THAN 70PSI. 7. if it goes over the pressure you want repete steps above exept loosen the nut in about 1/4 to 1/2 turns untill you reach the desired pressure 8. if it does not reach your desired pressure then you do the same thing exept tighten the nut in 1/4 to 1/2 turns untill you attain your desired pressure. 9. when the pressure is reached, replace cover so you dont risk rusting the contacts. if you need more help feel free to email me. and i will assist you in any way that i can.
- Q: When I buy submersible pump, the other party did not inform is the aluminum submersible pump, water pump factory production of aluminum submersible pump illegal? Is it against the law to sell the pump to the pump without informing me?
- When buying, if you ask for a copper wire or a wire, and don't answer you, it's against the principle of good faith. On the contrary, if you did not ask to buy the water pump with aluminum core, then there is no violation. Because the country does not have any laws and regulations prohibiting the production of aluminum core wire motor, naturally there is no aluminum wire motor as a fake and shoddy products, there is no pre notice obligations.In fact, the aluminum core motor is good, and the price is low, especially in the dry environment of small and medium-sized motors, with good performance. Only used in submersible pumps, because aluminum is easier to damp than copper wire, due to bacteria and other corrosion, and its life is sometimes less than copper wire. But the water pump, aluminum often needs to rewind coil, because of a small submersible pump motor is not good around general scrap.
- Q: How many pumps does a 50 meter water head use?
- Considering the pipe resistance and the water head, it is recommended to use the pump at 65 meters or so!
- Q: I have oil all over my water pump. I investigated when I saw a few drops of oil in the garage that showed up every few days. I then saw a drop of clean radiator fluid. Does oil come near or through the water pump? I have a 96 nissan maxima if that helps.
- you have blown the head gasket it seperates the water from the oil do not drive the car it will ruin the motor
- Q: After the pump has the control box, but also the power distribution box, the control box and the distribution box is not the same box?
- What you are saying is not a concept. The function of the control box is to control one or more equipment and to protect the equipment. The function of the distribution box is to distribute the power. The control box is connected to the power box, and the power box may be responsible for several devices at the same time. The distribution box is just one of them.
- Q: Engine problem 1999 Nissan Sentra 4 cyl Front Wheel Drive Automatic 165000 miles ---------------------------------------------------------------- I have a leaking water pump that has to be replaced. I am calling around getting prices and some people tell me that I have to do the timing chain at the same time and that will be a great deal more money. Can I just replace the water pump? It seems that the water pump only will be about 200.00 but both could be 500.00. Please help
- I don't know about a 1999 Sentra specifically, but when I replaced my water pump in my 96 Saturn SC2 I didn't have to do anything timing belt. Unless the mechanic says it just needs to be replaced the two items should not be related.
Send your message to us
Submersible Water Pump QDX1.5-15-0.37
- Ref Price:
-
- Loading Port:
- Ningbo
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 5000 set/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
