Hot Dip Galvanized Steel Wire 2.5mm For Razor Wire

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Commercial Galvanised Steel Wire

(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .

(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .

(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.

(4) Tensile Strength Range

(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.

(6) Packing

(7) Zinc Coating

Meet GB/T 15393 standard.

Q: I'm replacing the ground wire in a chandelier because it has been cut by the previous owner when it was removed from the ceiling. Overall it is pretty simple and I have everything diagramed. When I went to Radio Shack and bought the replacement wire they gave me 18 gauge solid insulated hookup wire. It looks totally different. The ground wire is a braided copper wire (7 strands). Should I go back and take my copper wire with me and get copper or is what I have just as good? An electrician will do the installation of the chandelier into the ceiling.: Ground wire is common convention at electrical boxes. Ground wire from point to point in any circuit is part of the wiring cable used. On a ceiling light, there is little danger of electrical shock if there is no ground wire from the fixture to the metal box. However, your replacement wire will work just fine.

Q: wiring has ceramic poles: That must be some OLD wiring. All you can do is be very careful. This would be a good time to consider putting in new wiring.

Q: I'm trying to tighten the electrical wires on my car.Do I just use pliers and twist them tighter?Can I use my hands?-tightening the wires on my ignition switch and starterNeed to know asapNo B.S. just need to know how: I think that twisting with a pair of pliers is best, less chance of getting a nasty metal splinter in your skin.

Q: Where can I purchase small wire of a large quantity that is similar to wire on cellular phone chargers?The wire im looking for needs to handle no mare than 12 volts.: Belden is a good source, there are lots of other. But I suspect you want a multi-wire cable, not a wire. You need to specify the number of conductors, and the size of each. The 12 volts is not relevant. The insulation voltage is. Also, note that for long runs, you have to increase the wire size. .

Q: other than soldering and using a T-tap (wire tap), what are other common ways of connecting two wires together? Also, what does the following video say at the 1 minute 10 second mark? It's a something-set that helps to attach wires.: wires can be welded or brazed (which is a little different than soldering) and mechanically attached (wire nut or screw terminal). THere are some electrically conductive pastes and adhesives. The ends of the wires can be immersed in a container of Hg (but this is getting farther away from common ways).

Q: I have this sony x plod headunit that i want to install.unfortunetely i do not know the wiring on it. i could find out as i go along which wires go to which speakers... but which two wires are the POWER wires?so i attached pictures but the basic layout is on the left side there are 4 sets of two wires (im assuming they pair up vertically)on the right side there is a long black wire with a metal hook on the end.: Black wire with metal hook is the ground. Red connects to switched 12V. (...12V when ignition in RUN or ACC position) Yellow connects to constant 12V. edit: I think the blue wire is for a power antenna.

Q: im installing an amp and i have no clue what to do with thw power wire.... I read to cut open my steros power wire (usually the blue) and wrap my power wire around it... I found the blue wire but there was a tag... Caution Remote output only... This is not the wire for power supply. please connect this wire to the remote for the amplifier... Does this mean i just connect this wire directly to my amp?: ok wait hold up. so the only wire that should be hooked from the amp to the headunit is your speaker wires, remote turn on wire, and your rca cables. ....What you need to do is get the power cable(usually red) run it from positive on the battery to the POS on your amp. next put your ground wire from the GND on the amp to bare metal on your cars chasis.

Q: how to wire a receptacle with 6 wires?: I say that JimW has given you the best answer ..... sounds to me that the box that those wires are in is a connector or in-line jumper box ---- where is your multi-meter or 2-wire/glow tester to find whatz hot .... the certified electrician is going to do what JimW says ... further tests will prove it .......

Q: have a kenmore dryer with 3 wires now had it will not dry need info on wiring it so it will dry: each so often the wires will take a 'set' and in case you lay them decrease back in place. i do no longer think of that there is a good or adverse cord, the sensor is entirely a swap that completes the circuit. yet there will be a wiring diagram on the decrease back of the dryer and you should appear at it to verify how the wires run and persist with it decrease back. desire this helps you with it. good success.

Q: what wires connect from the vehicle to the a/f sensor: Why do u want to know what wires go to the sensor? If you have a code for the a/f sensor..99 % of the time it is an open in the sensor itself. On rare occasion there are others like a chewed wire by a rodent. But I would just recommend replacing the a/f sensor. And i u were to follow the wires from the male connector they would lead you to a big wire harness that basically just all ends up at the ECU. Just in case u wanted to know.

Send your message to us

*Email

*TEL

*Quantity

*Unit