Stainless Steel Grooming Tub

Hot Products

Two Blass Handle Chrome Plated Brass Body Faucet

Three Blass Handle Chrome Plated Bathroom Sink Square Faucet With Shower

Hot Sale Antique Plated Faucet With Three Handles And Shower

Modern Rose Gold Plated Bath Faucet

Contemporary Bathroom Faucet Kitchen Faucet MSCN-16575

Antique Brass Body Basin Faucet

Contemporary Bathroom Faucet Kitchen Faucet MSCN-16584

Antique Brass Body Basin Faucet With Two Zinc Alloy Handles

Antique Brass Body Faucet With Two Zinc Alloy Handles

2014 New Square Design Handle Brass Tap

FAQ

Im trying to replace my faucet sink in my bathroom the bolts wont come off ! I tried using the wrench I have but it wont turn what can I do? is there another tool I can use

The nuts that you need to remove are under the sink on the bottom of the faucet. Sometimes if they are corroded it's easier to undo the water lines and take the sink out and turn it over to get to them.

Seek the toilet water pipe specific height

General wash basin about 450mm or so, shower about 1150mm or so, about 500mm Pa pond, toilet about 250mm or so, and wash basin and squatting pan distance of about 400mm, toilet and bathtub water distance of about 500mm or so, but also according to The details of your home bathroom, the above data for reference only.

I am getting pebbles clogging up the cold water side of my bathroom faucet, whats up with that?

If you have just had work done on the plumbing, you could be seeing sediment from the interior of the pipes that was dislodged during the work. I find it odd that you are seeing this only on the cold water side (assuming you mean you don't have a mixer, but separate taps?). Don't install a water softener, as softened water is very bad for you, your children, you pets, and your plants. See what a plumber has to say about it.

I have a Kohler (sp) faucet in my master bath that's come loose. I've looked underneath for some kind of bolt to tight, but I don't see anything there to tighten. I'm wondering if it was fitted badly and the means to tighten it lays between the plywood and the granite top. Thoughts?

Because you'll NEVER get a standard wrench up in there (I've tried, trust me), you'll have to pick up a cheap basin wrench at your local hardware store. See below link for pic.

i try to fix it myself.i can't seem to unscrew that white plastic ring, it was really tight. so what should i do now? should i hire a professional?

You have to unscrew the white rings and pull out the faucet. Clean and dry the water from the sink and faucet. Then put plumber's putty around the bottom of the faucet and reattach it. Make sure it's tight because water leaking from the bottom of the faucet is what's causing the leak. This happens when water splashes in the lavy and around the faucet. That's how the water seeps through. If you can't take off the "white rings," Home Depot sells a plastic nut wrench for about $18, it's made by Rigid. It's the easiest way without breaking the white rings (nuts). Or buy a basin wrench for about $8-$10 for a generic model.

Is the size of the washbasin single-hole double-hole faucet the same?

Pitch is the center of the standard 10 cm, is the same

How is the detachment of the Crowe basin?

Still can not be demolished, you can brush some kerosene on the screw, so that kerosene soaked into the screw (about 2-4 hours) after the demolition; can not be removed to the faucet, the faucet can be cut off

Hansgrohe basin basin with what basin

According to the spool to points, can be divided into rubber core, ceramic spool and stainless steel spool and several. The most critical of the quality of the faucet is the spool.