Environmental Control Systems

Hot Products

FAQ

Buried extension butterfly valve is buried or need to repair the valve well, can build the valve well, the extension rod butterfly valve installed in the valve well, the extension rod to avoid covers, the top of the valve well out, so that the hand wheel in the ground operation.Atlas S143 is less than the inner diameter of DN150 valve wells only 1200mm, DN200-DN250D diameter of only 1400mm, 700mm valve covers, valve rod and a handwheel to lengthen through the valve cover, valve wells is built to cover the embedded pipe or tube? Is there a standard atlas?
It is better to set up the valve well for repairing the valve later;If it is extended to reveal the valve well, the waterproof of the well must also be considered. Otherwise, a rainy well will be full.
valve adjustment 2001 chev prism 1.8L
valve adjustment . you need to know the fire order. the gage between the stem. rotators the cranshaft. it could be cold start. cylinder need to be bottomed center.
Butterfly valve D41W-1, 41, W, 1, respectively, what does that mean?
D--- stands for butterfly valves; 4--- refers to the form of flange connections; 1--- refers to the valve stem and disc in the center of the valve line, without eccentricity; w--- refers to the valve seat material and body material is the same, usually carbon steel. The final 1--- refers to the nominal pressure of 1 kg / cm2.
I have a 1993 Oldsmobile Cutlass Supreme and I think I have the case of the blow-by. The engine had high mileage, but was rebuilt b/c it stalled while driving. 3.1L V6 gasoline engine. The fuel filter and the fuel pump are brand new. Now we have the same problem a few months later. It stalls while driving. Its been sitting a while and won't start by itself, so I pulled off the air intake hose off of the air filter to spray starting fluid into it. I noticed oil puddled in the air intake hose, so I looked for the PCV valve on the rocker cover. There is a tube going from the air-intake hose to the rocker cover. I popped out the tube from the rocker cover and there is no PCV valve. Just tube. Is that where the PCV valve is supposed to go? If not, where can I find it on the engine? And could that possibly fix the blow-by and the stalling engine? I'd appreciate any help. Thanks in advance.
pcv valve is on the valve cover closest to the firewall.it is attached to a rubber hose that runs to the intake. right below an electrical plug
For example, the arrow above is from left to right, and the direction of my current is from right to left. Is that ok? I have a diameter of 700 of the hard seal butterfly valve is so installed, but it will leak water, it will not leak, very serious
The direction of the arrow on the valve body is cast, refers to the flow of media, users see the arrow, the arrow direction according to the logical and installation, this installation has become a habit, it is easy to accept the installation instructions, according to the national standard is not what error. But in the eccentric butterfly valve is installed so that sometimes there will be some problems, said the following example: according to the flow of eccentric butterfly valve with the medium flow consistent installation, tube medium is liquid, after the valve is closed, if the original direction of medium inlet pressure, reduced or zero, the export of medium reflux reflux, if senior supply, resulting in the high pressure medium, the pressure is greater than the inlet pressure, the valve will be subjected to reverse pressure, because the hard seal butterfly valve as a one-way valve so that the use is not conducive to sealing butterfly valve, and there will be leakage.
I have 1993 Seville 4.9. I got a new EGR valve but it didn't help. I tested it with vacuum pump, it won't hold pressure at all, same with old one. Is that new EGR valve bad or just different type of EGR that vacuum pump won't work? Thanks!
The first source, pages 20-22, lists all 9 basic types of EGR valves. Not all the types are vacuum operated, but check out #5 and #6 - they behave very differently from each other without a real live exhaust system connected to them.
Does the pneumatic butterfly valve need electricity?
Pneumatic butterfly valve generally not need steam can Shandong Yuhong automatic control valve
The difference between the directly buried gate and the flange valve and butterfly valve
The flange gate valve is stable and reliable when used in the pipeline, so the flange gate valve is used on the high pressure pipeline.Butterfly valve refers to the closure of parts (valve or butterfly plate) as the disk, around the valve shaft to achieve rotation and closing of a valve, the main cut off on the pipe and throttling role. Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis of rotation, so as to achieve the purpose of opening or closing or regulation. Butterfly valve used in furnace, coal gas, natural gas, liquefied petroleum gas, city gas, hot and cold air, chemical smelting and power generation environmental protection engineering system, conveying a variety of corrosive and non corrosive media pipeline, used to adjust and cut off the media flow.