100ah Lithium Battery

Hot Products

CECOX 4000W All in one Battery with long life LFP Cell and IP65 grade

Panama warehouse spot inventory 10kwh household lithium batteries for solar system

51.2V 100AH 5KWH Wall Mounted Lihtium Battery for Solar System Panama Warehouse

Factory price 5kw inverter and 10kwh lithium-ion battery all in one storage energy system

Stocked In Africa Wall Mounted 51.2v 100ah Lifepo4 Battery Powerwall

Low Voltage 2.5KWH 5KWH LiFePO4 Ultra Thin Wall-Mounted Home Energy Storage Battery

Factory price stacked energy storage lithium ion battery 48v 100ah 5kwh 10kwh 20kwh

Home Storage All in one Battery with IP65 VPP and IOT JX Good Quanlity

wall-mounted home solar storage lithium battery 51.2v100ah (JX)

14KWH Home Lithium Battery KS3 for Solar System Spot Inventory Panama Warehouse

FAQ

What are the technical parameters of the battery?

Usually the capacity of the power supply is expressed by kV · A or kW. However, as a power supply VRLA battery, the use of security (A · h) that its capacity is more accurate.

The role of the battery?

Battery is widely used, can be used for ups, electric cars, scooters, cars, wind energy solar systems, security, and so on.

Maintenance-free battery how to detect it?

Check the height of the electrolyte at least once a month. There is no mark line of the battery, the electrolyte added to the plate 10-15mm can be higher; there are two red line of the battery, the electrolyte can not exceed the red line above.

80ah how much battery storage capacity?

Is 80AH. Understood to discharge at 80 amps for about 1 hour (but not to say that after 1 hour is finished, there is still electricity). In theory, this is your battery power.

What kind of battery is divided into?

Ordinary battery: ordinary battery plate is composed of lead and lead oxide, the electrolyte is sulfuric acid aqueous solution. Its main advantage is the voltage stability, the price is cheap.

What battery does the van use?

The most obvious feature of lead-acid batteries is the top of the plastic cover can be unscrewed, there are ventilation holes above. These fillers are used to fill pure water, check the electrolyte and the use of exhaust gas. In theory, lead-acid batteries need to check the density of each electrolyte and the level of liquid, if there is a need to add distilled water. But with the upgrading of battery manufacturing technology, lead-acid battery development for the lead-acid maintenance-free batteries and colloidal maintenance-free batteries, lead-acid batteries do not need to add electrolyte or distilled water. Mainly the use of positive electrode to produce oxygen can be absorbed in the negative oxygen cycle, to prevent water reduction. Lead-acid water batteries are mostly used in tractors, tricycles, car start, etc., and maintenance-free lead-acid battery wider range of applications, including uninterruptible power supply, electric vehicle power, electric bicycle batteries. Lead-acid batteries according to the application needs to be divided into constant current discharge (such as uninterruptible power supply) and instantaneous discharge (such as car to start the battery).

How to repair the battery?

Pry open the adhesive or heat-sealed battery cover, reveal the maintenance-free battery rubber exhaust valve, carefully remove the exhaust valve, save, observe the battery internal situation. Add 0.1% to 0.5% of the electrolyte to the battery, just to the battery above the flow of electrolyte. At the same time, check whether the black impurities, if there are obvious black turbid impurities, indicating that the battery plate has been significantly softened, the possibility of battery repair is relatively small. If there is no black muddy impurities, need to wait 4 hours later, the water fully into the battery. If it is only because the deactivation time is long and cause the battery capacity to decline, do not need to carry out this step operation, should go directly to step 3 pre-charge.

How should the battery be well maintained?

Electrolyte density This is to evaluate whether the battery charge is normal, whether the aging of the important parameters, the use of density meter or electrolyte density tester can be measured. If the electrolyte density is too small, you need to charge. And the electrolyte concentration is too thick or too thin to a certain extent, it means that such as the occurrence of plate vulcanization, short circuit or overcharge phenomenon, this time on the need for maintenance.