small bore hydraulic ram for boring machine 2010-2014

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specifications

1.ISO9001:2008
2.Seal:Merkel or Parker
3.Working pressure:16-25Mpa.
4.10 years of experienc
5.Material:CK45

CMAX series engineering hydraulic Cylinder

(1)working pressure:16MPa

(2)Piston diameter: 40-250mm

(3)Seals:Merkel or Parker

(4)Sensor: MTS or Balluff


BOOM,ARM,BUCKET CYLINDER
R55R60-5-7R130R200-5R210-5R220R225-7
R260LC-5R280R290R300R305-7R450-5R215-7
R210LC-3R335-7     
cylinder diamete r      (mm)
piston rod diameter (mm)max stroke (mm)
40202225500
50252832600
63323545800
804045552000
904550632000
1005055704000
1105563804000
1256370904000
14070801004000
15075851054000
16080901104000
180901001254000
2001001101404000
2201101251604000
2501251401804000        




Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How is the hydraulic jack refitted into a high pressure inflator?
As long as the pressure of the air pump is large enough, of course, the compression resistance of the hose should be good enough, and the speed problem can be solved by the reducing joint.Test method:1. remove the hydraulic jack refueling refueling Pusey, down on the square on the tin.2. release the hydraulic jack release valve and release the oil.3. remove the lift lever and use the +0 wrench. 8 meters of pipe clockwise unscrew the small pump, using a pointed nose pliers to pry open the gasket, remove the 6# ball.4. hydraulic jacks clamped in a vise, use pipe wrench will cap loosens counterclockwise, remove.5. beat the coat with a leather hammer and take it off.
Q:UG4.0 parts library, what cylinders, motors, cylinders are standard parts for the equipment?
I give you an online version of it, can go to the site to download the linkable.partcommunity, I have been using CAD material, can download, support UG format and some other CAD format, no requirement for computer system.There are a lot of gears, bearings, such as motor, Oriental motor, MISUMI Schneider, Misumi etc.. There are more than 400 manufacturers of product models, massive.
Q:Kobelco 330 6e excavator hydraulic pump overhaul after the car is going to hold
The engine has to be overhauled with strict standards. The following are the important "indicators" for the engine to be overhauled. The signs are that the surface engines will be overhauled.1. cylinder pressure difference: cylinder compression pressure should be consistent with the original design requirements for tachometer, cylinder pressure gauge inspection does not meet the requirements for the unqualified cylinder pressure difference per cylinder pressure and cylinder average pressure difference less than 8% with tachometer, cylinder pressure gauge or engine analyzer to measure (does not meet the standards of the Elantra engine the cylinder pressure difference required for unqualified). When the engine cylinder pressure is lower than its Wyatt standard value will have a serious black smoke.2. idle fluctuation: engine idle running stability, the speed meets the original design requirements. The speed fluctuation is not more than 50r/min. The tachometer is used for running test or by engine comprehensive analyzer.
Q:Can the hydraulic jack be changed?
Yes, as long as the pressure of the air pump is large enough, of course, the pressure resistance of the hose should be good enough, and the speed problem can be solved by the reducing joint.Test method:1. remove the hydraulic jack refueling refueling Pusey, down on the square on the tin.2. release the hydraulic jack release valve and release the oil.3. remove the lift lever and use the +0 wrench. 8 meters of pipe clockwise unscrew the small pump, using a pointed nose pliers to pry open the gasket, remove the 6# ball.4. hydraulic jacks clamped in a vise, use pipe wrench will cap loosens counterclockwise, remove.5. beat the coat with a leather hammer and take it off.6. pull out piston rod, such as pulling out, put out the base with pointed nose pliers rectangular rubber ring valve hole, pour 8# ball, with a long stretch in the end mouth gun oil discharge valve seat hole inside the air, need to control the volume, the piston rod will pop up, aim at the wall, avoid injuries caused by pop-up.7. remove the nylon seal of the hydraulic jack piston and then put the piston rod back into the cylinder. Use the tubing to clamp the cylinder against the counter clockwise. Thus, when the pipe clamp is pulled on, the deformation of the oil cylinder can be avoided and the clamping flat can be avoided.8., with self tapping screws into the steel ball block, with pliers pull out the block, take out 6# steel ball.9. all parts of the hydraulic jack are cleaned with diesel oil and dried with an air gun. The holes in the base are blown with an air gun, and the inside of the cylinder is observed with a flashlight. Is the inner part of the pump smooth?. Replace it if it is not smooth or damaged. Observe whether the three steel balls are round and smooth.
Q:Is the cylinder usually faster than the hydraulic cylinder?
When the compressed air flow is the same as that of the hydraulic source, the speed of the cylinder and the hydraulic cylinder are the sameIn actual use, the general air compressor low pressure air compressor driven by the same motor power output than hydraulic machine, so the result of the action of hydraulic cylinder cylinder than subconsciously think fast.
Q:The main difference between hydraulic circuit and pneumatic circuit
The hydraulic pressure should be returned to the tank, and the pneumatic can be discharged directly into the atmosphere without any waste or pollution!!
Q:Why is the digital hydraulic cylinder not widely used?
1, the movement of the plane to do a guide rail, to limit the movement of track;
Q:What does hydraulic cylinder type "HSG 80/60-1100" mean?
HSG refers to: hydraulic cylinder for engineering, cylinder bore 80mm, piston rod outer diameter 60mm, travel 1100mm.This is shorthand for you.
Q:Computer automatic packing machine, cylinder voice suddenly become larger, how to solve?
2 the hydraulic pump leaking into the hydraulic cylinder causes the hydraulic oil in the cylinder not sufficiently large to be injected, resulting in no action of the hydraulic cylinder;
Q:How to remove the hydraulic cylinder oil seal?
Is the O ring squeezed out? The front cover should be threaded, carefully to see if there are holes installed, there should be 2 or 4, is not to be painted over, if not, must use the flat shovel.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range