new hydraulic ram, telescopic hydraulic ram, hydraulic telescopic ram for tipper truck

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1.ISO9001:2008
2.Seal:Merkel or Parker
3.Working pressure:16-25Mpa.
4.10 years of experienc
5.Material:CK45

CMAX series engineering hydraulic Cylinder

(1)working pressure:16MPa

(2)Piston diameter: 40-250mm

(3)Seals:Merkel or Parker

(4)Sensor: MTS or Balluff

Q: For example, I press a workpiece with a hydraulic press, and the pressure gauge shows 0.3MPa. Then I change the cylinder pressure. When I type, I choose the 0.3MPa cylinder instead of the inner diameter of the cylinder.: if you want to change into the cylinder pressure, enough on the line, in addition to consider increasing the oil return pipe of the cylinder, pneumatic actuator only because the system did not return with an air inlet pipe. The trachea.

Q: What is the pivot shaft in the cylinder?: Suitable for welding of tool and mould, high-speed tool steel, hot work tool steel, steel, cast steel, T-1 steel, Nai Zhengang, vanadium steel, spring steel, martensitic stainless steel, austenitic stainless steel, ferritic stainless steel, and the unknown as well as between the various different types of steel welding etc.. Such as high pressure valves, broken bolt clearance, shaft transformation, etc., the effect is very satisfactory.

Q: What are the conditions in the hydraulic system with the imported throttle valve? What is the difference between the throttle valve and the outlet valve?: 1. pairs of single rod hydraulic cylinder, import throttle speed into the non rod cavity, you can get more speed than the oil back throttling speed

Q: The cylinder is the same as the cylinder, crane: The medium of the cylinder is liquid (oil), and the medium of the cylinder is gas (nitrogen, compressed air, etc.)

Q: What is the difference between the cylinder seal and the cylinder seal?: The medium of bees is different. One is gas sealed, and the other is liquid sealed.

Q: UG4.0 parts library, what cylinders, motors, cylinders are standard parts for the equipment?: There are a lot of gears, bearings, such as motor, Oriental motor, MISUMI Schneider, Misumi etc.. There are more than 400 manufacturers of product models, massive.

Q: Hydraulic cylinder application: Construction machinery, construction machinery, cement, power, electronics, machinery, medical equipment, packaging machinery, etc.. Is a telescopic movement of the body. ?The use of a very wide range of cranes from our daily saw, automated assembly line, small to the hospital some small hydraulic beds, etc., are widely used hydraulic cylinder, cylinder equipment.

Q: How to use hydraulic system to control the feeding of machine tool table and the positioning and clamping device of workpiece: Two, the role of machine tools:A lathe is a machine tool for turning a rotating workpiece with a lathe tool. Can also be used in the lathe drill, drill reamer taps Banya and knurling tools for the corresponding processing. Lathes are mainly used for machining shafts, disks, sleeves, and other workpieces with revolving surfaces. They are the most widely used machine tools in machine building and repair factories.

Q: always have hydraulic oil leakage, please expert advice, with what seal can avoid, the best zero leakage.: 200 / min work frequency, high viscosity, slow flow, affect operation sensitivity.It is precisely the year that is too low to cause disclosure. Try to increase viscosity properly.This is a contradiction.

Q: There is oil in the tank. Is it the cylinder gasket? Some people say that the serious thing is the cylinder block cracking, I would like to know the excavator cylinder block under what conditions will crack the body? It's not cold, not frozen!!: What you say is possible, the steel mat will be, the steel body will also be frozen,

Send your message to us

*Email

*TEL

*Quantity

*Unit