Hydraulic Pump AP4VO112TE CNBM CMAX MADE IN CHINA
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Hydraulic Pump AP4VO112TE CNBM CMAX MADE IN CHINA
In AP4VO112TE series of hydraulic axial piston pump, electrical proportional valve is used to control the angle of the swash plate to achieve independent control by single pump. In this way, the engine power is thoroughly used to make it possible to adjust the engine output power according to actual hydraulic power, which increases greatly the machinery’s performance.
Rated Revolving speed | 2200r/min |
Pressure rating | 35Mpa |
Displacement | 112ml/r×2 |
It is featured with high power density, strong suction capacity, long life expectancy and low noise etc. This series of pump is used for crawler-type hydraulic excavator of 36-40ton as well as various open circuit hydraulics.
With years of unceasing efforts, CCHC now owns dozens of products of Three systems and Four Series. At present, CCHC provides mainly solutions of hydraulic system for hydraulic excavators and produces customized products.
Rated Revolving Speed | 2000r/min |
Pressure rating | 35MPa |
Displacement | 112mL/r×2 |
Specifications
1. CE certification
2. ISO9001:2000
3. Brass impeller, carbon steel motor shaft, with thermal protecton inside.
- Q: 498, just play the crankshaft, not oil, engine oil pump is new, and another one or not
- Check to see if the tile is leaking or leaking. Is there a leak or drain in the oil circuit? Is there an injector on the crankshaft? Is there any improper installation?! I hope my answer will be helpful to you!!
- Q: First question: I mean the turn key, the engine doesn't work, the seconds when the starter works. Does the oil pump inject oil into the engine during this time? Or wait until the engine is fully started to inject lubrication?The second question: because now the cold weather, I saw a forum of northeast riders turn the key to the starter operation recommendations for 1-2 seconds, then later normal launch, said that this can reduce engine wear, do this operation is correct?
- The first problem: the oil pump and the engine crankshaft movement synchronization, start the machine work a few seconds, the oil pump oil pump in the same way, just because the empty oil engine cooling period, not immediately to the oil pump in place.The second question: basically, there is no such operation necessary, when the engine does not run, the oil pump will not pump out oil, reduce the wear and tear of little effect, but more start will increase the wear of the starter.
- Q: What will happen to the old Bora oil pump?
- Oil lamp alarm, shake, abnormal sound, I hope I can help you
- Q: Does the abnormal sound of Audi Q5 oil pump need replacing?
- If it is determined that the abnormal sound of the oil pump is to be replaced!
- Q: The car oil pump is broken. What are the problems?
- If you lose the oil pressure, the alarm light will go on, and continue driving will cause fatal harm to the engine!
- Q: What is the cause of engine oil alarm?
- Check the oil shortage first, if the oil is not missing, check whether the oil sensor is damaged, the line is normal, if there is no problem, check the bush.
- Q: My motorcycle has been running for a long time. Now, about 2 bottles of motor oil in one hundred kilometers are too expensive. Can you add the engine oil to the mailbox according to the approximate proportion? Thank you.
- You'd better not put it in the tank. Will affect the gasoline combustion, because the oil concentration and gasoline is not the same. And the functions are different. What is the place with what place, with a little or no big problem, but the exhaust pipe will take the blue smoke, the damage to the engine is not great. If so, I suggest going to the 4S shop to take down the tank and clean it.The oil is added to the tank, depending on the type of oil (burning or lubricating oil) and the amount added. If it's the engine oil that has minimal impact on the engine, the mixing ratio should be within 1:25.If the amount of oil added to the tank is more than 1:25, the possibility of carbon deposition in the cylinder head of the engine will increase. Below this value can be assured to use, the smaller the proportion, the smaller the impact on the engine.
- Q: What are the markings on the fuel pump and the oil pump? They can be recognized at once
- This question is a bit wonderful to say, petrol pump is generally the only plastic pump heart is generally car iron sight to see and open the oil pump in the engine oil pan on the oil pan general can see are generally open Aluminum Alloy.
- Q: Sonata 6 cylinder morning taxi dadada big sound like the Volkswagen B5 engine chain expansion broken chain to the valve cover sound, car temperature reached 90 is not loud, and a high speed with the speed of 120 continuous driving not more than 20 kilometers, over 20 kilometers, more like a car with no oil if the valve is inside the chaos ring, and three cylinder ring, the outside does not ring, beg you master to solve!
- Cold car is a normal phenomenon. Please feel free to use it.
- Q: How to solve the blockage of the automobile oil pump?
- Remove the oil pan, remove the oil pump and clean the strainer with gasoline
Send your message to us
Hydraulic Pump AP4VO112TE CNBM CMAX MADE IN CHINA
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches