It convey the liquid evenly, continously and constantly from the suction to the discharge side.
- Q:What will happen to the old Bora oil pump?
- Hello, oil shortage occurs, I suggest you check as soon as possible, oil is the engine's blood, there is not enough pressure to clean the oil, the engine will soon be damaged. It is recommended to go to the repair shop to check the oil pressure immediately. If the pressure is not enough, the vehicle will not be opened for the time being. The pressure will be enough, it may be a pressure switch or a related line fault. Or advise you to overhaul as soon as possible, so as not to cause great losses!
- Q:What part does the electromagnetic valve connect to?
- The external solenoid valve is installed on the oil pump, and the oil pump solenoid valve is used to realize the oil pump two or multistage oil pump pressure, and is in the oil pan, but the position is the external of the engine.Built in solenoid valve installed in the oil pump, usually in the main oil road and oil pump, controlled by ECU, installation position in the cylinder.
- Q:How can Honda know when the pump is broken?
- Hello, use the oil pressure gauge to measure the oil pressure
- Q:What is the effect of excessive oil on the oil pump?
- Too much oil, will increase the rotational resistance of the crankshaft, reduce the output power of the engine, and the excess oil from entering the combustion chamber in the combustion, burning oil, causing the vehicle to take the blue smoke, and increased fuel consumption, oil residue after combustion (the main component is carbon, very hard) will accumulate in the combustion chamber wall. To reduce the space of the combustion chamber, thereby reducing the engine compression ratio, at the same time, will accelerate the wear of cylinder and piston so as to reduce the service life of the vehicle.
- Q:The car oil pump is broken. What are the problems?
- There's no trouble. You're not going straight
- Q:What are the problems caused by engine oil pump damage?
- Hello, the oil pump damage, will lead to insufficient oil or will not provide oil in the body parts of the lubrication, such as the size of the tile can not get the lubrication of oil, so that lead to burning tiles and other phenomena, thank you for reference
- Q:Where does the engine oil from the oil pump go?
- Let me add, the larger engine oil pump - the cooler - the main oil road - to the other oil ducts
- Q:I put down the motorcycle engine oil pump cleaning up after the cylinder head not to how oil ah
- The oil tank should be emptied into the air at the rear of the oil pump.
- Q:The motorcycle oil pump is broken. Can the oil be added directly to the tank?
- Most of the 2 stroke motorcycles can be added to the gasoline tank according to the quality of the lubricant and the lubricant: about 1:25~50 of gasoline. For individual 2 stroke engines, the use of this method may be detrimental to the crankshaft bearing because of the lubrication path, but as a contingency, or increase the proportion of the lubricant properly.If your 2 stroke motorcycle oil consumption is very large, you can adjust the supply of lubricating oil pump, so that the best position. I don't know what your car is. I can't help you exactly.
- Q:What's the use of the oil pump for motorcycles?
- Two stroke engine oil pump is regulated through cable, throttle in the middle line will be divided into two, one to one to the carburetor, the oil pump, the throttle fully closed, then adjust the speed nut oil pump on the cable, the cable to completely relax, this is the minimum amount of oil, but be careful not to too loose, when the twist of the throttle, engine oil pump should follow the action, there is a situation of oil pump through internal wear caused by excessive amount of oil used for many years, this situation can not be adjusted, only the replacement of oil pump.
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average