It can transfer different liquids with lubrication feature and no particles or corrosion, so that they have been widely used in hydraulic pressure, lubrication, fuel oil and onveying etc.
- Q:How long will the oil pump lubricate the engine parts after the engine is started?
- 1-3 minutes, the cold car is usually 3 minutes after refueling, the door started.
- Q:What are the fuel pump inspection items for diesel generator sets?
- The main inspection items are as follows:1, the outer rotor and pump casing pump clearance;2, the internal and external rotor meshing clearance;3, rotor and pump cover face clearance;4. Flatness of pump cover.[diesel generator unit oil pump inspection notice]1, check valve planes such as abrasion, sag, pitting phenomenon, application of grinding paste on the plate grinding, severe cases should be renewed.2. The surface of the one-way valve seat on the shell should be replaced when worn or not smooth.3, the top rod and the top sleeve wear seriously, so that the gap increases, the seal becomes worse, diesel leakage seriously, you need to replace with the shell, or choose the enlarged size of the top rod, but need to pass mutual research.4, the coarse strainer tubing joints within the core, and easy to be cottony sundries plug, effect of fuel supply, it should always pay attention to the clean fuel and remove the dirt on the filter core.5, the hand pump piston rubber ring damaged, should be replaced in good time. After the center of gravity of the oil pump is assembled, the moving parts of the piston, the ejector rod and the other parts of the oil pump are required to be in good motion during the whole journey, and no blocking and blocking are allowed. The hand pump should be light and flexible. Pay attention to the installation of the one-way valve spring. The check valve spring must be accurately embedded in the spring slot.
- Q:Are the engines all organic?
- Sure. How else does the oil work?
- Q:The role of automobile gasoline pump
- The oil pump is the role of the engine oil to the friction parts, the oil circulation lubrication in the road, in order to ensure good lubrication. The engine oil pump is composed of gear pump, gear pump body and other components. When the engine works, the cam shaft drives the drive gear pump rotation gear oil whip. Along the inner wall of the pump from the oil inlet flow to the outlet, the formation of low pressure, resulting in suction oil inside the oil is sucked into the oil inlet and the oil outlet. The oil product more, thus the pressure increased, the oil will be pressure to the friction part, realize the forced lubrication.
- Q:What about the oil leakage of automobile oil pump?
- If the oil pump is broken, replace it, if it is a rubber pad, change the cushion.An oil pump in a lubricating system that forces the oil from the oil pan to the engine moving parts. Used to increase the pressure of the oil and to ensure a certain amount of oil.
- Q:How do you install the pedal motor pump?
- Apart, remember, where appropriate, hammer Zang Zang. (means gently tapping)
- Q:What is the driving oil pump of the car?
- This is what you want to see the car electric appliance compared to older car distributor is driven by the camshaft now the car to the lubrication oil pump is working hard to directly influence the performance of vehicle engine oil pump car now mostly use crankshaft driven thus eliminating the intermediate links are the system when the oil pump speed more directly
- Q:What is the influence of insufficient oil supply in the oil pump?
- Will cause abnormal engine performance and output power decline. Difficult to start; the car is weak; the car will shake when it opens
- Q:Does the motorcycle oil pump break down and cause the engine oil to burn?
- The pits are ready for oil, lubrication, and burning
- Q:Does the abnormal sound of Audi Q5 oil pump need replacing?
- If it is the oil bar, if there is a sound, the abnormal sound must be replaced, this is beyond doubt. I hope my answer can help you
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average