Q:DO i TWIST THE WHITE AND RED SMALL WIRES TOGETHER UNDER THE WIRE NUTS ON AC WIRING TO THE CONDENSER?

what you have is a thermostat wire it is a two wire so if one is not connected and the other one is wire the ones that are not connect together regardless of color. wire manufacturers vary their wire color but the all work the same make sure to tape it up after you do it so it don't fry your transformer in the a/c unit..follow the blue wire to contactor on the opposite side of where it hooks up there should be another wire follow it and you will see where it is broken twist that wire to the one that is unhooked then put the wire nuts back on

Q:Most of the peoples know that i am a tv junkie and love to watch episdes wire episodes and others as well but what if i want to watch wire episodes online.i mean what would you guys make most use and also like to recommend?

Full okorder Download - The Wire - 3x11 - Middle Ground Download - The Wire - 3x10 - Reformation Download - The Wire - 4x13 - Final Grades Download - The Wire - 4x12 - That's Got His Own Download - The Wire - 4x11 - A New Day Download - The Wire - 4x10 - Misgivings Download - The Wire - 4x09 - Know Your Place Download - The Wire - 4x08 - Corner Boys Download - The Wire - 4x07 - Unto Others

Q:During a lab experiment, a straight piece of copper wire is connected across the terminals of an AC generator and the current through the wire was measured. If the wire is removed and a part of it is tightly wound into a loop of many coils and the wire is then reconnected to the generator, will the measured current through the wire be greater, lesser, or the same as it was before the wire was coiled? Explain your answer.

bypass to the factors save and get a Chilton's! That way you're becoming photos appropriate in front of you to adventure up your application. They value approximately $15! the remarkable $15 you will ever spend. appropriate now you will have all your wires back on and not dropping time top right here with idiots which will greater suitable valuable than probable supply you the incorrect answer as nicely!

Q:hi to all, pls try to help me,, to get the kawasaki zxr250 cdi color wiring diagram!?i hope that you help me..i really hope that i use my kawasaki big bike,.....thank you !!!!!rose,,

Wiring diagrams are always black and white. Do you need a wiring diagram for your bike, or do you just want one in color?

Q:i got a fi bl 15dual 2 subwoofer. im wiring it down to 1 ohm.now for the problem. lets say im wiring the positive terminals together. am i suppose to wire it all with positive wire or can i also use negative copper wire? i used two positive wires and one negative wire to hook up the three positive terminals. is this bad? do i need to make all of them positive silver wires?

ok well either red or + is positive and black or - is negitive, the problem i have is you said you had 3 positives and one negitive on a dual coil sub,?? if you mean you ran all 3 wires to your amp then its wrong, if you mean you ran 1 wire to your positive,1 wire to your negative, and 1 wire from the other positive and negative together, then you have gone up to 4ohm and not down to 1, you should have 2 positives and 2 negatives, hooked together to make 1 positive and 1 negative as for the wire colors, they sometimes differ so you can tell them apart, providing your the one who screwed them to the amp, i run mine copper positive and silver negative, but each to there own.

Q:I have a 5 pin ignition. I have Black and red wire coming from behind the starter.Yellow wire on the other side of the engine that is connected to the magnet by the fly wheel.Where do I put these wires in the ignition switch. ____ ____ __

You need to hook three wires into a five terminal switch? You aren't helping us much with any usable information. The yellow wire is the kill wire from the magneto. The black and red wires are hot from the battery and feed to the starter solenoid, assuming the switch has a start position. You need to check each terminal on the switch with an ohm meter to determine which function it serves and test the black and red wires with a volt meter to determine which one is hot now. Better still, why don't you specify the make and model, even the serial number if you can get it, and ask if anyone, including your local dealer, has a wiring diagram for that particular machine.

Q:What is the wiring for one headlight on a fourwheeler that has high and low beams.

one terminal on the bulb is common to both low and high beam. that will be the ground. the other two are the hi and low beam supply .take a test light and see which two of the three wires has power to ground . once the two hot wires are identified , the third wire will go to the common terminal on the head light bulb. take the other two and see which is hi and low by switching the switch and connect to the bulb . test the light before reinstalling it if there is no power at the wires than the problem is somewhere else

Q:My house is currently wired using Cat-5 lines. If I were to replace the Cat-5 wiring with Cat-6 wiring, would I see an increase in my DSL speed?

you have to have speical equipment to use cat-6, so no if you did that it would still be the same as using cat-6

Q:pendant wiring hookup. issue: light is always on house wires: red, white, black, ground pendant wires: green, white, black (and a ground wire to the frame) I did connect red to green, white to white, black to black, ground to ground is connecting the red to green the problem causing the light to be always on? do I just disconnect the red to green to fix?

No the problem is the black is a constant hot intended for a ceiling fan motor connection. #1) Bare and green are grounds only and no other wire should be attached to them. #2) The red should have been from the switch intended for a light fixture or kit. But it must not be attached to the wall switch or you would have tripped the breaker. I take it there wasn't a light there to start with? Are there any other wires in the ceiling box you didn't mention? If so please edit your question with more detail.

Q:the 2 wires that is connected from the key hole is cut .. how to fix or replace?

If there enough wire left on each side of the cut, say 1, then you could bear about 1/4 of the wire on each side and solder the wires back together making sure you are soldering the same wires together and wrap each soldered connection in electrical tape so they are not able to touch each other. Then a final wrap of tape around them both. If you are not up to soldering you could go to an auto parts shop and get a crimp connector to do the job, again bearing of wire is needed to get a contact through the cut area. If the cut is closer to the switch then there is no option but to replace the switch.....