Q:1980 ford f150 300 engine i need the wiring specs for the back lights thank you for any answers

what okorder and go to the repair manual section.. Autozone has older (10 years or older) vehicle repair manuals online.. check it there as most include the wiring diagrams

Q:What Spark Plugs and Wires would optimize my MPG? 2000 Bonneville SSEI

AC Delco plugs wires. Using substandard low end aftermarket cheap junk doesnt help your vehicle at all also replacing spark plugs wires really doesnt improve your MPG unless its misfiring badly

Q:When I am wiring my sub to my amp, what gauge of wire should I use? The sub is 750 rms and the amp is 700 rms. And how do I wire a 2 ohm sub DVC to a 2 ohm stable amp?

12 gauge would work fine or maybe good to an audio shop and get some thing better

Q:I don't like wiring nuts because I always feel like it's not a solid connection, like it could come out.

Wire Nut Alternative

Q:I am building an ice chest boombox and want to wire a toggle (on/off) switch to turn the amp on and off....the amp is wired directly to the battery....my question is that I am using 6 gauge wire....but can't find any female spade connectors that are 6 or even 4 gauge to hook to the terminals on the switch.....what is a simple way to do this....am I going to have to solder the wire straight to the terminals?

Why not wire the toggle switch into the remote + wire? The one that turns the amp on and off with the head unit. 7/5/2013**** Leave the power supply wire alone. The thick 4 gauge wire that runs from the battery directly to the amp, leave it alone, don't put a toggle switch inline on that wire. Instead there's a wire from your head unit (or ignition) that runs to your amp, it turns on the amp when the head unit turns on or your ignition key is in the on position. It's usually 16 or 14 gauge. That's the wire where the toggle switch belongs. Look at your amp, this wire I am speaking of is probably labeled remote+ or ign or something like that and it's usually located next to your power and ground connections on the amp.

Q:How much wire is required?

Length of wire is L = R*A/p SI units must be used, so convert radius to meters: r = 0.0254 / 64 m using 25.4mm = 1 inch r = 3.969*10^-4 m (0.3969mm) So cross-sectional area is A = pi*(3.969*10^-4)^2 m^2 A = 4.95*10^-7 m^2 The average resistivity of nichrome is p = 1.1*10^-6 ohm-meter So the required length of wire is L = 2.2 ohm * 4.95*10^-7 m^2 / 1.1*10^-6 ohm-meter L = 0.990 m

Q:Wired car radio no sound powered on then wires crossed had to run red straight to battery. Then memory and ground crossed. Now nothing. Checked fuses radio fuse is bad. Will i also need a new wiring harness? Stereo Works fine when hooked up to battery charger.

Could you rewrite your question and clear it up some. The red wire should go to the ignition on the existing harness in the dash. You were crossing all of those wires? Look at the diagram that came with the deck to know which wires go where. Typical pairs of wires (white and white w#x2F;black stripe or gray and gray w#x2F; black stripe) are for the speakers, red is for power(ignition) I think green is the signal wire and so forth. I don#x27;t know how your wires just get crossed like that? Did you splice them into the wrong ones in the dash?

Q:Would crepe paper stick on chicken wire?

Crepe paper needs an adhesive to make it stick to a surface, such as white glue. However, it gets messy once dampened, as the colors may bleed. Instead, I would consider working with paper mache or plaster gauzing strips, which would provide a strong skin over the chicken wire. Both can be primed with gesso then decorated with acrylic paints. If this is a sculptural piece you want to keep, we would also suggest varnishing it for protection.

Q:Hello, i am trying to hook up power windows in my truck. the motor has two wires and the switch has 3 wires. i just need the relay. i just need to know what kind of relay i need and how to hook it up. i know i need a reversing relay and that it needs to use the 3 switch wires along with the two motor wires and the two power wires. does anyone know what this relay is called and where i could find it online? thank you.

a 3 phase motor has 3 windings whose centers are separated by 120° mechanically. The phases in a 3-phase system are separated by 120° electrically. The sum of the magnetic fields produced by these currents has a constant magnitude, and rotates the direction determined by connection of the phase wires. Arbitrarily giving ABC as one direction of rotation, then BAC = ACB = CBA reverses the rotation of the field in the motor, reversing its rotation.

Q:I NEED TO CHECK IF A WIRE IS GOOD ON A FITNESS MACHINE. HOW DO I KNOW IF ITS GOOD? WHAT SHOULD THE OHMS BE?

This is true for most wires of practical sizes in devices like fitness bikes or treadmills. If you have a multimeter, you will find there is a setting for reading resistance, which is marked in Ohms. If you set the meter for that setting, you will notice that when you touch the red and black probes together, the meter will read ZERO ohms or close to it. There is a little knob somewhere to set it to zero. Then you can read a wire by touching the probes to the opposite ends of the wire. If the wire is sound, the reading will again be zero (equivalent to touching the probes together). If you don't get zero, the wire may be damaged or corroded. Watch for corrosion, which will give you a high-resistance reading. If the wire is one conductor in a cable with numerous wires in it, you will have to look for the opposite ends of the same conductor. They will probably be color coded, which makes it easier. Good luck.