Fiberglass Best Composites FRP Gratings
- Ref Price:
-
$3.00 - 10.00
/ m²
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 10 m²
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Introduction
FRP Molded Grating is a structural panel which uses high-strength E-Glass roving as reinforcing material, thermosetting resin as matrix and then casted and formed in a special metal mold. It provides properties of light weight, high strength, corrosion resistance, fire resistance and anti-skid. FRP Molded Grating is widely used in oil industry, power engineering, water & waste water treatment, ocean survey as working floor, stair tread, trench cover, etc. and is an ideal loading frame for corrosion circumstances.
Feature
Corrosion Resistance
Fire Resistance
Light Weight & High Strength
Safety & Anti-slip
Electrical Insulating
Aging Resistance
Specification
Advantage
coated with prevent aging layer
excellent insulating performance
no maintenance
high strength
long service life
easy installation
Application
Power plants, substation equipment enclosures, antimagnetic, anti-static,to prevent small animals into the equipment failure, as there is electricity facilities and without power interval intervals.
In high voltage electrical equipment for power line work, in order to prevent workers go wrong location, charged interval or near electrically charged equipment to dangerous distance.
Pool railings in sewage treatment industry
Corrosive chemical industry equipment around the fence
All kinds of building maintenance section
FAQ
1. How about the documents after shipment?
After shipment, we ll send all original documents to you by DHL, including Packing List.Commercial Invoice, B/L, and other certificates as required by clients.
2. How long is the delivery time?
Usually it takes 10-25days after receipt of the deposits or L/C, and it also depends on the quantity of your order.
3. How's the payment?
Telegraphic Transfer(T/T) or Letter of Credit(L/C)
PROCESS
FACTORY
- Q: Bathroom shower room walls should be waterproof?
- Toilet waterproof height, the State Construction Commission stipulates that the national standard is 1.8 meters, housing construction in the building has been made waterproof, waterproof layer extends from the ground to the wall, higher than the ground 250MM. But the metope of waterproof is not, according to the conventional bathroom waterproof layer on the shower head wall height of not less than 1800MM, average thickness of not less than 1.5MM, and the water after the end of the project must be done 24 hour storage experiment.
- Q: I need to know what pillows resources are used to make pillows and if they are natural resources or not. I need to what the pillow case, pillow stuffing and the pillow skin is made out of.
- Some pillows are stuffed with feathers, some with buckwheat, some with polyurethane foam. Pillow cases these days are usually a combination of polyester-cotton, some are silk, some are 100% cotton, some are satin, some are 100% polyester
- Q: Do they wear wigs same to ours? or there are some special wigs designed for them?
- I am glad being the first one to answer your question. People with cancer they are likely lose their hair for going through chemos. so lots of them want to wear wigs to cover their bald head. I think monofilament wigs are good for your friend. Monofilament wigs, not like other kinds of wigs which are made with cloth, is made with polyester and nylon material. women who have sensitive skin should choose them when they buy wigs. Because they don't irritate the scalp like wigs with cloth inside.
- Q: I‘m making a fake lance out of styrofoam. I need to coat the surface of the styrofoam with something that will make all those little bumps go away so when I paint it, it looks better.I just want something easy that you can buy at a craft store for under 25$. Does anyone have any recommendations on a product I could use?
- You most likely have air trapped in your brake lines or may not have tightened the bleeder valve well enough. Then again, what you are describing is the exact same scenario I experienced when replacing the brake calipers on my bike. I, like you, was bewildered at why my new calipers would not build hydraulic pressure. However, what I didn't realize is that it takes an insanely long time to prime the brake lines. I was priming the lines on my SV1000S for 15 minutes before they finally built pressure. I don't know if you flushed your system like I did, but it sounds most likely like air bubbles - also factor the age of your bike when considering leaks.
- Q: Ok so I have no clue about fiber glass and I‘m even wondering if lowes or Home Depot have it they sell fiber glass insulation whatever that means.Anyway I‘m trying to make a car part for my honda and I‘m wondering to myself is fiberglass easy to work with what are the fundamentals is it a lot of sanding down or just molding etc etc :/
- There is more than one kind of fibreglass Fiberglass insulation (sometimes called Pink) is just insulation and goes inbetween the walls. That is all. They are 2 different animals. The other fiberglass is like a cloth that is used with polyester resin in moulds to make boats(mainly) The Chevrolet Corvette is made of fiberglass (mainly because they could not bend metal to those extremes for the body the same fiberglass is used (always with the polyester resin to make a host of other things such as lawn furniture and to make structures like Disneyland and other stuff.
- Q: Hi all, I want to make a fiberglass subwoofer for a 10. I saw a few videos on how to but they use a cloth and put something that make it hard but i dont know what is that so can anyone tell me the steps on how to make it and what I need or any video that can help me please. I dont want to pay anyone to do it because is a lot money and I enjoy doing it my self for fun and I can learn at the same time. tyx all for the help :D
- i bought fiberglass and resin at a paint and plastic store to make my box
- Q: Can glass fiber plastics be used for food grade?
- Non food, no such restrictions. But it must conform to the relevant product specifications to be applied.
- Q: i want to make a fiberglass helmet (kinda like a power ranger full head helmet but no where near as lame lol) iv been looking for ages for help on howto use fiberglass what materials and how to use them but while people talk about it they give very little help on how to actually do it so if anyone has a walkthru or a guid on how to fiberglass a mask from scratch i would be in their dept as im a noob at it and need as much help as possible thnx :D
- Make a clay or plaster base to sculpt the fibreglass over. DO NOT cast it onto your face! Fibreglass resin heats up when curing, would burn you, the fumes would knock you out and good chance you would die. Make a base for the mask by molding if from clay, letting that dry, then seal it with a few coats of paint (spray paint is good) The base won't last forever not being fired, but would be fine for the fibreglass casting. The paint will help keep it from sticking. You can also make a plaster form too- just make a reverse mold in the clay then fill with plaster, and when the plaster is dry peel off the clay. Then again, cast the fibreglass over that. The fibreglass directions will depend on the brand. You usually have to mix 2 liquids together, then use pieces of fibreglass woven fabric to give support, alternating layers of the resin and embedding the fabric into it.
Send your message to us
Fiberglass Best Composites FRP Gratings
- Ref Price:
-
$3.00 - 10.00
/ m²
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 10 m²
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
