Black Annealed Tie Wire With High Quality

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Black Annealed Tie Wire

type of hole:round hole/square hole

tensile strength:350N-450N/mm2

elongation:20%

wire diameter:16GA/18GA

packing:3lbs/coil or 3.5lbs/coil

20coils/carton

1. We buy material from powerful companies ,so we can promise the quality.

2. Our engineers are very professional , and some of them have more than 20 experience.

All of our workers are conscientious ,and we believe the quality is our life.

3. We have advanced equipment,and our production line is in high level.

Q: My tail light work but when i hit the breaks everything go out. Any answers? Standard 4 wire: probably not a good enough ground connection make sure it is wired correctly white wire is the ground yellow wire is the left blinker and brake light green wire is right blinker and brake light brown wire is tail lights

Q: when wiring subs to different ohm levels, does is matter what kind of speaker wire you use to connect to the + and - terminals? i mean like gauge wise of the speaker wire and such.: the larger the wire the better the current move through it, i likeusing at least a 10 gauge, im using 8 right now its also harder to get them caught some were and break them

Q: A street lamp weighs 200 N. It is supported by two wires that form an angle of 130° with each other. The tensions in the wires are equal.What is the tension in each wire supporting the street lamp?If the angle between the wires supporting the street lamp is reduced to 100°, what is the tension in each wire?: Problem 1: If the tension in the two wires are equal, the angle they make with the horizontal must also be equal. Always remember that a horizontal line is a straight angle; hence, it has a measurement of 180°. Let's look for the angle the wires make with the horizontal. 130 + x + x = 180 130 + 2x = 180 2x = 180 - 130 2x = 50 (Divide both sides by 2) x = 25° Each wire makes a 25° angle with the horizontal. We can now find the tension. The mass must be divided by 2. Using trigonometry, let's find the tension force. The divided weight of the lamp shall be the opposite side, and the tension force shall be the hypotenuse. sin 25° = (200 / 2) / Ftens Ftens = 100 / sin 25° Ftens = 236.62 N (Answer) The tension is 236.62 N in each wire. Problem 2: We use the same approach. 100 + x + x = 180 100 + 2x = 180 2x = 180 - 100 2x = 80 (Divide both sides by 2) x = 40° Each wire makes a 40° angle with the horizontal. Calculate the tension force. sin 40° = (200 / 2) / Ftens Ftens = 100 / sin 40° Ftens = 155.57 N (Answer) The tension is 155.57 N in each wire. Hope this helps!

Q: I'm doing a science project on resistance and I need several different types of wire. I know to use copper wire, but what else could I ask for at a hardware store?: Aluminum is the most common wire material besides copper. You can ask the hardware store if they have thermocouple wire, it is a pair of dissimilar metals coupled to vary resistance based on temperature and is hooked to you thermostat in your house.If you really want to get exotic you could get ACSR (Aluminum Conductor Steel Reinforced) this is used by the power industry for power transmission and distribution. This is an aluminum conductor with a steel wire braided into it.

Q: is there a way to wire an exit sign to a plug for an outlet receptacle?: First off, Aurthur A's answer is composed of several NEC violations; he may be going to electrical hell, if he doesn't shape up. Second, you did not say if this is a required exit sign. If it is, then you will need a licensed electrical contractor to install it; as most jurisdictions will not allow work in anything but the owner's principle dwelling to be done by unlicensed personel.

Q: does bigger power, ground, speaker wires give more power 2 the amplifier?: Bigger power and ground wires will help, up to a point. If your wires are already big enough that you don't have a significant voltage drop between the battery and the amp, then bigger cables won't help anything.

Q: You have been given two samples of wire: one nichrome, one aluminum. Describe a procedure you could use to determine which sample was nichrome and which was aluminum: If the wires are the same diameter and the same length then the only difference is the resistivity or ?ρ? of each since: ??Resistance = ρ???L ? A = 4???L ? (π???d)? ??????where??L = wire length ??and???A = cross-sectional area of wire ??or use??d = wire diameter Since the ρ_nichrome is much higher than the ρ_aluminum and given the two wires are the same diameter and length then if you connect the two wires in series across a battery, and measure the voltage across each wire, the wire with the higher voltage will be the nichrome wire because the voltage across the nichrome wire is:?V? = i???(R?) and the voltage across the aluminum wire is: ?Va = i???(Ra)? and the current i is the same through both wires and R? Ra ... or if you can just measure the resistance of each wire, ... the nichrome wire will have a higher value.

Q: I have a kicker cvr 12 inch 2 ohm dual voice coil sub (400 watts) and a kicker zx750 amp. how to wire?: MDC is correct. You need to remember anything that is run (+) to (+) and (-) to (-) is parallel. When you run this with one dual voice coil sub, or two subs together, and then bridge it at the amp in mono, you are actually supplying a higher percentage of power from the amp, and the amp will see an ohm load that it may not be able to handle, which will cause thermal overload and shut the amp down when it gets too hot. Running in series will bridge the ohm load up. In your case your 2ohms that you run in series will double your ohm load. Increasing it to 4ohms, and when you bridge it mono at the amp, the amp will see around a 2ohm load in mono. Good luck!

Q: Okay I bought a new light for outside my home. I called the electrician, he got the wiring from the ground and we added cement so we would bolt down the light. Now i need help adding a photocontrol.: yes, the photo cell will work anywhere, in fact it will probably work better where the light is not hitting it when it comes on. It will work longer if direct sunlight cannot get at it.

Q: Its the wire that goes up to the antenna,its flat,and . brown in colormaybe their is a tool that can be purched: I tried using a knife but ended up shortening more wire than stripping it. The copper wire actually comes through in two places. I use a knife to cut in between them and then I use a wire stripper to remove the covering on each side. The Muse

Send your message to us

*Email

*TEL

*Quantity

*Unit