Q:Hi, I just bought a Nintendo Wifi USB connector and every time I inputted in the usb slot I hear the sound but nothing comes out On the bottom right screen as well I try searching my computer and nothing please help me out

have okorder

Q:I have a pair of Behringer HPS3000 headphones, which work normally when plugged in to the amp with their own cord, but the right one stops working when I plug them in to my laptop, speakers or iPhone using a connector. I'm pretty sure it's not a problem with the connector, as my guitar worked fine when I would use the same connector to plug it in to my laptop.Any ideas what I could do?

It IS the connector. Your guitar is a mono source, while your other sources are stereo. It's probably a mono adaptor. Easy to tell, though: If it has one black insulating ring on the shaft of the plug, it's mono. If it has two, it's stereo.

Q:I understand that telephone splice connectors are designed to splice 2 or more phone lines. But can they be used to splice speaker wires? If so, would it make a good connection?

i have installed car stereos with scotchloks before with out any negative effects

Q:i have a 1995 ford ranger 2.3l and i cant find the self-test connector can anybody help??

According to the factory service manual, the Data Link Connector is fastened to the bottom of the instrument panel, near steering column.

Q:I have a 95 Chevy Lumina with a headlight out. I don't think it's the bulb since the filament appears to be in place. I bought a headlight connector replacement from AutoZone and am now wondering how to do the installation. Do I need to solder the wires once I splice them? Also, will it be obvious where I need to cut the old wires off?

First, before looking at the bulb, check the fuse. They may blow at times. If you find it blown, DON'T just replace it - find the reason first, remove the cause (usually a short of some kind) and then replace. If the fuse checks ok, check the bulb. Filaments at times do appear in place even when they are not. Do the ohmmeter check or, if you don't have the instrument, install temporarily the bulb from the other side, observing bulb-handling rules (or you might end up with another blown bulb). If the bulb proves ok beyond any doubt, check the voltage in the connector terminals - there may be a broken lead (you'll need a voltmeter or a test bulb). If that tests ok (voltage ok with lights switched on), it's not the connector - it's something else. The only remaining reason may be the ground connection, a common problem in many older cars. To check that, install a temporary ground lead from the battery neg. terminal directly to the connector (try not to short the circuit).

Q:I have a pdx 1.1000 amplifier and the PREOUT Input RCA terminal is broken and I cannot get it fit right. I've tried everything, please don't tell me how I can fix this connector. I just want to know if I can solder the RCA connector to the metal part of the terminal. Not the gold plated one, but the 2 little prongs sticking out on both sides and with the gab in the middle that goes down into the board.

Don't do that the wire will end up ripping the connector loose and you'll lose your signal, your connector and your wire end. Instead, open the bottom of the amp, and solder the connector back into place. If the circuit board is cracked, (which it probably is so you need to at least check it inside before you do anything) make jumper wire connections to re-connected the broken circuits. Visually inspect and trace the pathways to replace them. Signal wires can be 16 gauge, but amp circuit wires should be sized according to the wattage of that channel. then maybe get a female end rca wire and cut it into a short tail with the female connector hanging out of the amp, and solder the wire ends into the right places. Do it right or pay the price

Q:does the Gameboy Micro use a standard GBA connector cord like the SP and advance? I'm considering buying a micro but if I need to spend an extra $40 on a special cord than I aint gonna do that

no. the gb micro has a different connector cord for everything. you cant use any cords on it that worked for the original gba or gba sp because the gba micro is much smaller than either one of the first two gba models. dont get it. its not worth it. gba micro is not worth your money at all.

Q:I have bought a computer Power SupplyUnfortunately all of the connectors are SATA and my drives are all Molex PinI know that I can use the SATA wires and combine it with a spare Molex connector that I also haveWhat color of the wires will I combine with the 4 wires of the Molex, I remember my 1 or 2 wires of the SATA will be disregard I'm just not sure what color of the wire it isthanks guys!!!

I'd okorder

Q:I recently bought a case with 2 usb ports and a firewire port on the front. i was wondering if all motherboards would have the connectors to hook them up or if there is something i should be looking for.Thanks

all motherboards has front panel connectors, it is located in the lower right of your motherboard if you hold it in normal position, refer to the manual or diagram of your motherboard how to connect these wires leading to front panel.

Q:First of all, where can I find a nintendo USB connector and does it work with a wpa2 wireless router. I need to be able to get wifi on my ds games. 10 points for the best answer.

nintendo 3ds supports wpa2. :) just saying. the nintendo wifi USB connector looks like a flash drive, this device is use for those who doesn't have wireless router. you just need to plug it on your computer WITH an internet connection. (you use this because your computer is connected via ethernet(cable)). after you connect the nintendo wifi USB. Only your DS or Wii can detect the internet connection. Try looking on game shops :)