Q:i have a 300x1 @ 4ohm and 600x1 @ 2ohms, i wanna hook it up at 2 ohms what gauge wiring kit should i get?

Your link isn't complete. One thing I do know, many cheap speakers come with speaker wire that is about the size of a hair and practically impossible to do anything with. I just buy 18 or 24 guage wire in a spool to hook up the speakers. Using the next size wire doesn't hurt, but smaller wire will reduce performance.

Q:I have installed a new wiring harness on my trailer, and two new LED trailer lights. The tail lights work, both turn signals work, but for some reason, I do not have a brake light on the right side. Both lights are grounded to their own post, and I do have a good ground on the coupler of the trailer. If a turn signal and brake light in a 4 wire system are using the same wire (green in this case)- how can one work, while the other is not? Any good ideas? I really appreciate the help.

Not all cars (imports) can run on a 4 wire system. (they look like they will work when testing or locating wires, but don't when all hooked together). Adapters are at the car parts store, but not cheap.I would first try running the trailer lights with one power wire touched to the three wires, then hook up a stabber type elec tester and see if the problem might be at the car circuit. Do the car lights work right? Would get a jumper wire and jumper the trailer to the car and each light on the trailer to the frame. You may be getting a back feed ground on the circuit somewhere. All the temp grounds will tell you where the problem is.

Q:I am connecting a humidstat to furnace. I would normally use furnace/thermostat wire for this purpose except that I need 8 conductors and the largest furnace/thermostat wire seems to be 5 conductors. I would like to use another 18guage 8 conductor wire but not sure if there are any specifications I need to ensure it meets before I can use it inside furnace cabinet.

they do make 8 and ten conductor stat wires but in a pinch you could run two 4 conductor wires side by side. just make sure you mark at both ends becayse you will have 2 of each color wire. mark them as red 1 and red 2, etc.

Q:What are the advantages / disadvantages of different types of wire (ethernet, coax,twisted pair) over the different types of wireless( WI- Fi, bluetooth)

wireless is slower than 10/100 according to readings on p c wireless is mainly for convenence

Q:Im Very Curious As To How Did The Designer Orese Make Her, African Continent Shape Wire Earrings? I Have The Supplies To Make Wire Earrings. I Would Love To Do A Personal DIY! :~)

as well as on the first page link above, under the category Wire-Framing (P.S. Why did you use initial caps on all words in your question?...kinda hard to read.) .

Q:One wire has part of the plastic coating on the end, the other wire does not.

the lead is the wires showing. lead wire can also mean attaching a wire and feed it through a wall attach other end to the wire and pull it through. Now if you need both ends to have wire showing take a utility knife firmly place wire on block of wood and lightly cut through the caseing. thats the thick wire that en cases the other wires and peal back and then cut it off. then carefully hold blade of utility knife and wire aganst your thumb on a 45 degrees away from you and pull that will strip the plastic off the wires hope that answers your question dave

Q:I moved into a home with pre-wired speakers. There is a bundle of speaker wire coming out of the wall. Each wire has 4 colors of other wire coming out of it. There are a total of 7 main wires (with four wires each) and a total of 9 speakers.

4 conductor wire has a few neat uses. 1 is to bi-wire your speakers. Meaning that if the speaker has 2 red and 2 black terminals then remove the bridge and run the cables to the posts separately thus increasing surface conduction and increasing output and sound quality. Also if you are running cables in the wall to 2 speakers that are near each other or to a single stereo speaker then you don't have to run 2 separate 2-conductor wires. This would also be true if you are running to a second zone using an in wall volume control. If this is the only wire you have for a standard speaker connection it won't hurt to twist them together at both end (pos with pos/ neg with neg) and serves the same purpose as using thicker cables.

Q:plzzz let me knw tis !! GRADE 10 PHYSICS- importance of live wires neutral wires !!!!!!!!!!

These two wires provide the voltage difference (called potential difference) that is responsible for driving the current through an appliance. Live and neutral are terms most commonly use with mains electrical supply .. they are equivalent to + (live) and - used with batteries and other DC sources. The live wire is at the higher voltage (most dangerous) and the neutral is usually close to ground voltage (0 V). Both wires together form the complete circuit required for the current .. from the supply (through the live wire) to the appliance and back to the supply (through the neutral wire). In a mains circuit a switch is always connected into the live wire so that the high voltage is disconnected from the appliance. A switch connected in the neutral wire prevents the appliance from working (so it appears to be off) because there is a break in the circuit .. but the high voltage is still connected to the appliance which may be dangerous. For the greatest safety a switch should disconnect both live and neutral wires at the same time.

Q:could someone teach or explain to me how to hook up the 1st one, i do not understand what is happening there. How do you connect thoes wires to the main wire??? the distribution?

Ok, first thing you want to do is, for each subwoofer, wire a negative and positive together. You can use regular speaker wire to do that (well you're supposed to anyway). After that, you will have a negative and positive terminal left on each subwoofer. What you need to do is run a speaker wire from each of the terminals, so you have 6 different wires from 6 separate terminals. Make note of the 3 positive wires and the 3 negative wires. Now what you do is simply twist together the 3 positive wires together, so you have 1 positive wire. Connect that positive wire to the positive terminal of the amp (if it's a 1 channel amp. If it's a 2 channel, connect it to a bridged channel on the positive terminal. Or however you want.) Do the same for the 3 negative wires. Twist them together to have 1 negative wire, and connect it to the negative terminal on the amp. Finished! That kind of wiring is called Series wiring, by the way. The other kind is called Parallel wiring.

Q:In constructing a large mobile, an artist hangs an aluminium sphere of mass 6kg from a vertical steel wire 0.50m long. On the bottom of the sphere he attaches a similar steel wire, from which hae hangs a brass cube of mass 10kg. How would i calculate the tension in each wire?

The length of the wire is inconsequential unless you're calculating stretch. The tensile force in the upper wire is simply: Fu = 6 + 10 = 16 kg The tensile force in the lower wire is simply: Fl = 10 kg If you want tensile stress, then you need the wire's cross-sectional area.