1.Endure chemical corrosion well ,do not get rusty,have good is acid-resisting , alkali resistance and Able to bear corrosivity
2.Have self-extinguishing and flame resistance: will not spontaneous combustion , also not combustion-supporting
3.Ageing resistance is good: can use 30-50 years between degree of 15~60.
4.Fight electricity well.
5.Wall is smooth, wall surface tension is little , is impossible to formscale deposit.
6.Quality is light, it is convenient that install moves to unload.
7.Cleaning:do not influence water quality, will not change the composition of water quality .
8.The water of prevention of leakage.
1.The civil architectural facility of water supply system.
2.Swimming pool, play water prowls facility project.
Size and coding:
- Q:How can I get really stuck in pet hair out?
- i know man the hydrant needs a funeral lol!/
- Q:How can I start to get rid of my three huge fears?
- This might have been caused by a spirit or two, but highly doubtful. unless they were on the pics. I'm a sensitive channeler my spirit family can move objects, dial phones, play video games, definitely break things.
- Q:Hydraulic pipe joint seal, with raw meal belt and sealant that good?
- Use sealant.It is not recommended to use the raw meal belt and can not be sealed. It will cause oil leakage. The raw meal belt will be contaminated by the oil, which is particularly easy to cause the phenomenon of the valve or plug the oil control port. If you must use the raw meal belt, then you must pay attention to the coil when you can not bring the raw material out of the joint, so as not to be sucked into the tank by oil.
- Q:Macbook issues with my "Control" button?
- It is not recommended because the fit is not as designed. In very low pressure non lethal services like air or water you might do this and be okay but If you did it for a high pressure service like natural gas and there was a problem later, you would have to justify why you allowed it.
- Q:I would like to ask who has 24 degrees taper hydraulic pipe joint processing drawings, please send me, thank you very much
- If you can, then I have thousands of pipe joints drawings, are the original pipe joint processing factory technician to do when painting,
- Q:The pipe line of the hydraulic pressure pipe is formally installed
- 2.2. common thread is used for the connection and fastening between the mechanical parts, and the general thread connection is mainly made of coarse thread. The thread strength of the fine tooth thread is slightly higher than that of the same nominal diameter, and the self-locking performance is better.Mark 3. metric screw thread: M20-6H, M20 * 1.5LH-6g-40, where M represents a common thread metric, 20 nominal diameter thread is 20mm, 1.5 pitch, LH said, 6G 6H left, said thread precision grade, precision grade of internal thread uppercase, lowercase precision grade of said external thread, 40 screwing length;3.1. commonly used metric ordinary coarse thread pitch as shown in the following table (threaded hole diameter: carbon steel = nominal diameter P = nominal diameter cast iron; 1.05~1.1P; processing thread rod diameter = nominal diameter: 0.13P):Table 1 diameter / pitch of common metric coarse tooth threadThe nominal diameter of P cast iron bottom steel bottom thread rod diameter pitch P cast iron bottom bottom rod diameter of external thread steel
- Q:physic helppppppppppppppppppp?
- The outside diameter must remain the same on pipe under 12 inches because much of it is threaded. Over 12 inches most pipe joints are welded together.
- Q:installing auto locks for sunfire?
- Not since 1977,when they added foil shielding to the outside.The radiation would cause the pacemaker to malfunction.You still should try to limit exposure,because the microwaves are generated in a magnetron and the pace maker is turned off by a magnet.Rapidly turning it on and off shortens the lifespan of the unit and can cause mafunctions.High voltage also is to be avoided,they have a magnetic field around them from the excited electrons.
- Q:What are the sealing ways of pipe joints? Thank you
- PTFE raw tape. Sealant。 If it is steel and copper inside and outside the thread, as long as the tightening, what sealing material can be used.
- Q:How hard to setup my own turbo intercooler etc?
- Jessica Simpson; she's beautiful. I never understood what people saw in Brooke Shields.
With advanced technology and equipment, our company is really powerful and with strong technological development and innovation capability. With strong technical equipment . Looking into the future, our company sincerely hopes to establish long term friendly partnership with domestic and overseas customers for yielding richer harvest in return for our society as well as creating bright future.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||North America8 %
South America 10 %
Eastern Europe 1 %
Southeast Asia 15 %
Mid East5 %
Eastern Asia 5 %
Western Europe 2%
Central America 5%
Northern Europe 2 %
Southern Europe 2 %
South Asia 5 %
Domestic Market 28%
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||port of Ningbo,Port of Shanghai
||21% - 30%
|No.of Employees in Trade Department
||30,000-50,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered
|Product Price Range
||Low and/or Average