It widely applies to a variety of mediums with different property and viscosity because of special structure and selected different pump's materials.
Proper medium temperature: -10°C ~ 200°C
Proper medium viscosity: 1.0cSt ~ 300.000cSt
Food industry: Pumping food liuqid,wine,waste liquid or additive liquid Textile mill: Pumping fible liquid,dyestuff,printing ink,nylon powder liquid Paper industry: Pumping back liquor Petro industry: Pumping oil,grease Chemical industry: Pumping suspend liquid,emulsion,soda & salt liquid Ship building: Pumping residue oil,sewage or seawater Building industry: Pumping slurry,Cement Nuclear industry: Pump rediocative liquid Metallurgical & Mine: Pumping oxide or waste water,drain off water,liquid explosive Watertreament: Pumping slurry,sludge,additive liquid Power plant: Pumping coal slurry
Electric glue pump
High viscosity internal gear electric glue pump
internal gear pump, Electric glue pump
High viscosity medium,petroleum,chemical industry,paint,medicine,foodstuff and so on.
1.HT200; 2.ZG230-450 3.1Cr18Ni9Ti,OCr18Ni12Mo2Ti
Proper medium temperature
Proper medium viscosity
Packing seal,especially suited to delivery high viscosity medium.
1.Steady delivery without pulsation,little vibration and noise.
2.out standing self-priming ability.
3.The pump can delivery the varied corrosion medium if the proper material of parts selected in addition,the working temperature can reach 200°C.
4.The same rotary direction of internal rotor and outside rotor results in little wear and long operation life.
5.The pump’s flow capacity can be changed through adjusting the speed.
6.It‘s specially suited to deliver high viscosity medium.
By sea or air
25-45 days,according to order quality
Export standard wooden palet or user-defined
Electric glue pump PRODUCT ADVANTAGES
* Steady delivery without pulsation, little vibration and noise * Working temperature can reach 200°C * Out standing self-priming ability
* Little wear and long operation life
* Suit to deliver high viscosity medium
Send a message to us:
Q:Rotary vacuum pump does not meet the requirements of vacuum, what are the reasons?
(1) pump connected outside pipes, containers, pipes, joints and other leakage test instrument, large leakage, rotary gas plug exhaust sound big, and the gas and oil mist discharge, should find leakage cancellation.(2) the assembly of rubber of intake pipe is not proper, damage or aging should be adjusted or replaced.(3) plug hole, the vacuum degree can be decreased, put the oil, remove the tank, loosen the nozzle plate, pull out the oil inlet nozzle, dredge oil hole, try not to use cotton wipe parts.(4) the vacuum system has serious pollution, including containers, pipes and so on. It should be cleaned.(5) the spring of the vane is broken and should be adjusted.
Q:What does electromechanical vector pump mean?
It is a close set of mechanical and microelectronic technology. It adopts dual control center mode to control, and has a new water pump with logic control center and IPC control center.
Q:Suction stroke and lift of water pump
Lift pump lift pump can lift refers to the height, usually expressed in H, the unit is m. centrifugal pump lift to the impeller center line, divided by two parts. The vertical height from the pump impeller centerline to the water surface, the water pump to suck water up to the height, called water head, referred to as suction pump impeller; from the center line to the vertical height of the water tank, the water pump can put pressure on the height, called water pressure head, referred to as the pressure. The pump head = + suction head pressure water head should be pointed out that the nameplate marked head refers to the pump itself can produce lift, it is not with the pipe flow friction resistance caused by the loss of lift. In the selection of water pump, attention can not be ignored. Otherwise, will be pumping Sheung Shui.
Q:The water tank of the fish tank does not air out and only has the water outlet
The water pump is cut off, the intake pipe is drawn out, and the water in the air pipe is blown out, then the water pump is put on the surface of the water, and the air inlet pipe is inserted on the surface of the water pipe, and then the water pump is put back into the water, and the water pump is electrified. Try again several times at a time. It should be effective.
Q:How to select the fire pump?
Such as a large pressure of about 10m or about 0.1MPa} because the most unfavorable point fire hydrant requires more than 0.07MPa (7m) and 0.5MPa (50m) is not greater than the pressure, so unless the pump is located in the 50m Valley is still lower than the garage, or add to the valve (or the use of fire hydrant decompression) otherwise, it is 120m lift pump
Q:What is a gear pump for?
Oil pump casing wearIt is mainly the wear of the floating sleeve hole (the normal clearance between the gear shaft and shaft sleeve is 0.09~0.175mm, and the maximum shall not exceed 0.20mm). The gear work is affected by the pressure oil, the gear tip is close to the oil pump casing, and the low pressure chamber part of the pump body is worn. Another kind of wear is the circumferential wear of the work surface in the shell. This kind of wear is mainly caused by the addition of oil which is not clear, so the oil without impurities is necessary.
Q:What is the cause of the damage of pump bearings?
First of all, know your pump model, and what is the bad bearing, in order to accurately judge for you. Because in addition to some common reasons, the structure of different pumps, bearing damage caused by the reasons are different. Otherwise it is fraught with itching shoes.
Q:Pump unloading in hydraulic transmission,
Can be used for short-term shutdown, pump non-stopNo unloading, usually through the overflow valve back to the tank, high pressure, power, at this time insurable pressure, and so on
Q:Rules for operation of centrifugal pumps
3, start the pump, wait until the speed reaches the normal speed, slowly open the outlet valve, observe the ammeter at the same time, and control the current in the rated current range of the motor.4, the operation requires smooth operation of water pumps, no abnormal noise, no pressure fluctuations. The abnormal situation should be stopped in time.
Q:What is cavitation, centrifugal pump cavitation phenomenon how to solve?
In order to make the pump full of liquid, usually in the valve installed at the bottom of the filter screen along the suction pipe, the valve until the end against the valve, strainer prevents the solid material into the normal operation of the pump impeller damage or hinder the pump.