Submersible motor pump Amacan P
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 pc
- Supply Capability:
- 1 pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Design |
Overview of technical data
| Type of impeller | Axial; Open;Propeller |
| Type of installation | Close- coupled |
| Maximum drive rating | 700 kW |
| Impeller material (EN standard) | 1. 4517;AL-BRONZE |
| Type of bearing | Rolling element bearings |
| Drive frequency | 50 Hz / 60 Hz |
| Maximum speed of rotation | 1. 750 1/min |
| Maximum flow rate | 25. 200 m³/h |
| Casing material (EN standard) | JL 1030 |
| No. of impeller entries | Single entry |
| Casing material | Cast iron |
| Minimum flow rate | 360 m³/h |
| Suction characteristics | Non- priming |
| Drive voltage | Low voltage |
| eClass assignment | 36410101; 36410106 |
| Pump set location | 00 |
| Explosion protection | ATEX II 2G T3 |
| Max. permissible fluid temperature | 40 ****** |
| Free passage | 255 mm |
| Main applications | Energy; Mining / Dredges;Water;Waste water / sewage |
| Type of installation | Stationary |
| Type of casing | Tubular casing |
| Type of lubrication | Grease lubrication |
| Type of drive | Electric motor |
| Installation position | Vertical |
| Shaft material (EN standard) | 1. 4057.05;1.4021.05 |
| Type of coupling | None |
| Shaft seal type | Mechanical seal |
| Drive | Electric motor |
| Maximum head | 12, 00 m |
| Minimum head | 0, 80 m |
| Nozzle position | In- line |
| Casing partition | Radially split |
| Connection to power supply | 380 V, 400 V, 690 V, 3~ |
- Q: How does the centrifugal pump pump and cut the pump?
- Can not be generalized, the pump is divided into many categories, centrifugal, reciprocating, screw type, diaphragm type, and so on, the starting steps of each pump is not the same. The following is the centrifugal pump and reciprocating pump to do a simple introduction. Check the items and so on.Centrifugal pump: first open the pump inlet valve, pump exhaust, and then start the motor, slowly open the outlet valve. If it is a high speed motor or multi-stage pump, open the motor before the outlet valve slightly open.Reciprocating pump: slightly open the inlet valve of the pump, fully open the outlet valve. After starting the motor, at the fully open inlet valve.Here is a brief introduction. I hope it works for you.
- Q: The distance from the pump button to the ground
- A button is arranged on the surface of the fire hydrant button, and when the fire hydrant is started, the press button can be pressed directly, and the red starting indicator light of the fire hydrant button is on
- Q: I would like to ask, constant pressure pump set pressure 20Mpa, the actual load is 15Mpa, then the constant pressure pump outlet pressure? If it is 20Mpa, then where is the loss of 5Mpa? If 15Mpa, the constant pressure pump 20Mpa how to understand? In addition, the constant pressure pump pressure is defined when the flow began to reduce the point, or a sharp drop in flow after the point?
- The pressure loss is borne by the valve. Constant pressure pumps generally do not export direct load, unless you need this load response is very fast, then the maximum displacement of the pump work, so as to ensure the rapid response of the load.
- Q: Does vacuum pump oil belong to dangerous goods?
- Absolutely not. We often send oil by express or by freight. There are no problems at all. Don't be afraid, don't burn, explode
- Q: How many kinds of pumps are available and the operating principles of various pumps?
- There are many kinds of pumps. There are different classifications according to different standards. If classified according to the principle of work, can be broadly divided into the following four categories:1, vane pumps: centrifugal pumps, axial pumps, mixed flow pumps, vortex pumps, etc.;2, displacement pumps: piston pumps, piston pumps, diaphragm pumps and so on;3, power rotary pump: screw pump, gear pump, etc.;4 、 special function: jet pump, water hammer pump, magnetic drive pump, etc.;
- Q: How to distinguish the flow and displacement in the hydraulic pump? What's the difference between the two?
- The unit of displacement is the milliliter. How many milliliters does the pump rotate per circle? The displacement is the pump, the individual,The unit of flow is generally a liter, a figure added to the displacement of the pump over a period of time,
- Q: Pump operator's responsibility 10Sharing the rules, responsibilities, etc..
- 7., master the knowledge of concrete mix ratio, strictly forbid to add water to the pump at will.8., concrete mixing and workability, gravel diameter is too large, effectively refuse to pump.9. when the delivery pump fails, it can analyze the cause and quickly eliminate the trouble.10. pump complete, you must clean the pump body and pressure pipe residual.11. complete other temporary work assigned by the leader.
- Q: What are the characteristics of the piston pump?
- Piston pump is an important device of hydraulic system. It depends on the plunger in the cylinder in reciprocating movement, so that the volume of the sealing chamber volume changes to achieve oil absorption and oil pressure. Plunger pump with a rated pressure, compact structure, high efficiency and flow and easy adjustment, is widely used in high pressure and large flow and flow needs to adjust the occasion, such as hydraulic machine, engineering machinery and ships.
- Q: What's the submersible pump?What is a submersible pump, and what about it?
- Deep well submersible pump is a fountain, drinking water transportation, irrigation, hot springs, high-rise transport facilities, etc., deep well submersible pump excellent performance, so widely used in various fields.
- Q: How long does the fine stone pump need maintenance? What should I pay attention to?
- Check the line from the relief valve to the cylinder inlet to ensure that there is no external drainage or deformation due to impact and wear and that the connections are complete and fully tightened. - replace any damaged pipe immediately. - change the original settings strictly: all adjustments and calibrations can only be done by professionals. - no fucks hydraulic components, otherwise manufacturers on product warranties and liability shall not be responsible for. A warning because the hydraulic oil can reach very high temperature, there is the danger of burns, so open pipe fittings should take appropriate protective measures. Any replacement parts must conform to the level specified by the manufacturer. 8.2 check lubrication grease pump in oil at any time to ensure adequate and clean the lubrication pipeline joints without overflow phenomenon. Check the lubrication of the running parts at any time, and find the parts which lack oil, and check them immediately to prevent accidents. - check that the centralized lubrication system is effective daily. When the grease pump is empty, the grease added is often not easy to pump out because of the bubble. In this case, open the outlet of the pump, run the grease pump until the grease is re flowing, and then connect the pipe
Send your message to us
Submersible motor pump Amacan P
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 pc
- Supply Capability:
- 1 pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
