Q:like in movies how do you connect like some wire to start the car? also which wires? I'm curious not trying to take anyone's car.

Connect wire 'A' to wire 'B'...Briefly touch wire 'C' to wire 'D' (until engine starts) see figure 1. Disclaimer: These instructions are not to be used for illegal purposes...

Q:cat chewed two wires computer speaker wireand wii sensor bar wire well i can't just buy new ones or replace the wire so i need to reconnect them some how using insulated ferrules and electric tape and wire strippers any suggestions how to do this properly do i crimp them together with insulated ferrules or solder them together?what else can i do?i'm clueless how this worksneed help

My bird bit my phone cord in two pieces. Looked like a clean cut. I just stripped the wires, twisted each side together, then taped well with electrical tape. Now I keep all wires off of the floor.

Q:Does anyone know what color the amp sensor wire is on a 2005 EX?

DIRECTWIRE? WIRING INFORMATION - KIA / SORENTO / 2005 / Audio Radio 12v green + Radio Groundblack - Radio Ignition green/orange + Radio Illumination red/black + Factory Amp Turn-on Power Antenna N/A LF Speaker +/-brown - black +,- radio harness or amp under driv seat RF Speaker +/- green/orange - blue/orange +,- radio harness or amp under driv seat LR Speaker +/- green - blue +,- radio harness or amp under driv seat RR Speaker +/- blue - yellow +,- radio harness or amp under driv seat Sorry this doesn't list the Amp turn on wire, but now you know a buch of wires that it is not!! Good luck...if you test with a voltmeter, the amp turn on wire should not have 12v in any key position. MikeC

Q:A wire is 1.5 m ong and has a diameter of 1.5 mm. The stretch modulus of the wire is 6.2 x 10^10 n/m^2. If a force of 400 N is applied to end of the wire, then the increase in length of wire is??please help, thanks

The stretching of wire by longitudinal force: If F force applied across the crosectional area A of wire of radius r and lenght L then the wire elaogates in the dirextion of force Stress P = F / A A = pi* r^2 = (1.5/2)*10^-3 = 7.5 *10^-4 m^2 strain produced = dL / L = increase in length / original L Young's modulus or elastic (stretch) modulus for the maretial, within elastic limits, Y = stress/strain strain = stress / Y dL = F * L / A * Y = F * L / pi (r^2) * Y dL = 400* 1.5 / 3.14 (7.5 *10^-4)^2 * 6.2*10^10) meter dL = 0.005479 * meter dL = 5.479 millimeters increase in length

Q:I like bending paperclips to make things, does anyone know where you could buy spools of the wire paperclips are made out of.(any type of wire that is the same size and material will work)

For the best answers, search on this site https://shorturl.im/axqI3 No, I am afraid you can't ... you need a special alloy, not paper clips, which are mild steel.

Q:The outlet box has 2 black wires capped together, 2 white wires capped together, 2 bare wires capped together, and a single red wire. The light fixture I want to install is a two bulb fixture that has 2 black wires, 2 white wires, and 1 bare wire.

The wires on your ceiling fixture are called ROMEX. This is the big casing that has two insulated wires and one bare wire. The bare wire is the ground. The romex coming into the box comes from the source and the other comes from the switch. Black is HOT coming into the box from the Romex that has only the black and white wires. To be sure about this, take the cover off the switch on the wall and see what wires are present there. This might show that a three way switch is installed somewhere if there is two switches that control that light. As far as the light fixture that you have, connect the two white wires and the two black wires together and then one of those pair goes to the white wires in the ceiling box and the other goes to the red wire.

Q:What does the wire do for braces? What happens if you pull it out and everything else it ok?

The wire is like a train track and the teeth are the cars. Get rid of the track and the cars go off course. Wire is what is putting everything in place.

Q:I am in the process of installing a new thermostat, but I ran into the problem: new thermostat has 4 ports W, Y, R and G. But the old thermostat has 5 wires: W, Y, G and B. I am not sure where B wire (black color) should go. Do I need to look for another thermostat that has a port for B wire?

The black wire should be for ground. You and try to connect it without the black first to see if everything works ok, if it does tape off the black and tape it to the other wires. If not look at your UPM diagram and see which port is for ground and it should hook up with that wire. But I would double check with the heat pump wiring diagram to see what that black goes to and verify that wire with a multimeter.

Q:I have two DVC subs and I know how to wire them down to 1 ohm with the wires coming out of one outlet on the box but I don't know how to wire them down to 1 ohm with wires coming out of both sides of the box. Anyone have a wiring diagram for this?

For okorder /... On the inside of the enclosure, connect both positives and both negatives to the enclosure inside terminal. That makes each side of the enclosure 2 ohms. Mount and screw in the subs. Now, on the outside: 1) Observing polarity, run short jumpers between the terminals (positive to positive, negative to negative) and then connect ONE set of terminals to the amp (again observing polarity) (positive to positive, negative to negative. 2) Run separate wires from each set of terminals to the amp, observing polarity. That makes the final impedance to the amp 1 ohm.

Q:i need 175ft of 110 wire how much does it cost?

depends one the guage and copper prices fluctuate daily