Q:do speakers function better with thick or thin wires??

It depends. If you are just gonna wire the speakers and just play it with mid volumes or normal operating volumes. these wires weather thick or thin doesnt matter. but if you want to push the speakers to it's potential, you need a good quality wiring kit. mostly these are guage 4-8 wires or thick wires of course thicker wires more current it can handle .

Q:i have a 1989 Nissan 240sx and im trying to install an aftermarket Pioneer radio (DEH-P20), my car only has 2 speaker which are in the front right and left side doors, i've gotten many wiring diagrams to help me install it and im pretty sure i have connected the wires correctly. the only problem is that after i got done connecting it, the radio wont power on.. if theres a defective power wire, what can i do to fix it? and also, where EXACTLY do i connect the Ground wire? oh and why does the car wires have multiple same colors for example, theres like 3 light blue wires non striped from the car, etc.?thank you

240sx Antenna

Q:Two wires, 2.44 m apart, both carry current 2.2 A toward the bottom of the screen. The right wire is extremely long, and the left wire is 0.36 m long. What is the magnetic force on the left wire?

Magnetic force, F = BIL --------(1) where B is the magnetic flux density of the magnetic field caused by the right wire, acting perpendicularly to the left wire in Tesla I is the current in the left wire in Amperes L is the length of the left wire in metres To find B (due to the right wire), you have to use the formula B = (?0)(I)/(2πr) -----(2) where the I in this case is the current in the right wire, r is the distance between the two wires, and ?0 is the permeability of free space, numerically defined as ?0 = 4π×10?7 using eqn (2) so B (due to right wire) = (?0x2.2)/(2πx2.44) = 1.8x10^-7 T using eqn (1) and the value of B calculated above F = (1.8x10^-7 x 2.2 x 0.36) = 1.43x10-7 N

Q:The outlet box has 2 black wires capped together, 2 white wires capped together, 2 bare wires capped together, and a single red wire. The light fixture I want to install is a two bulb fixture that has 2 black wires, 2 white wires, and 1 bare wire.

It is obvious from the question that you have zero knowledge of wiring. While this is an extremely basic thing to do, I think it is better to get a professional so you and your house will be safe. Electricity is too dangerous to do without even the most basic understanding of safe procedures and standards. You will get people telling you how easy this is, but I would rather have you safe than try this your self.

Q:Wires in the dash*Radio constant*Radio Switched*Radio illumination**please match these up with the options below**Wires on the stereo itself*Dashboard Light Dimmer Switch*Amplifier Remote or Power Antenna (Positive +)*(fuze) yellow memory (negative -)*(fuze) red 12v (positive +)if someone could please help that would be great-since the wires were replaced i cant go by color

Car radio wire constant to stereo yellow memory. Car radio wire switched to stereo red 12v positive. Car radio wire illumination to stereo Dashboard Light Dimmer Switch. Don't forget to ground the black wire on the unit to the ground wire from the car harness. An extra ground strap to the chassis is a good idea also. If you don't have an amp or a power antenna, cap off the blue Remote/Antenna wire.

Q:I no longer have enough 0 gauge wire would it be bad to use 0 gauge power wire to the amp and 4 gauge wire to ground the amp?

Don't do it you will get allectorcutted.

Q:i have old wiring for a stove that iam putting in ,a new box but i have only 3 wires 2 of them are white and 1 black how should i connect on a 4 wire receptacle? on the receptacle 1 white 1 green, 4 a ground then it says x then y ???????

dont even attempt to wire it up. call an appliance service and they can test the wires for current and properly wire it up.

Q:I have a new light fixture I am trying to install. The electrical box has two sets of black and white wires coming in. Both of the black wires are connected together while the white wires from either set were used to connect the old fixture. How should I wire in the new fixture. The switch for this light has only one set of black and white wires connected to the light switch.

If you don't get it, you need to simply hire a qualified electrician so you don't screw up the fixture. Either that or see if there is a wall switch for the fixture for starters. Most people simply put black tape on the white wire that comes back from the switch because it is hot.

Q:1989 Honda Accord LxWhat is the wiring Diagram for the Stock stereo wiring harness?Just pulled out the old Stereo wanna put my deck in there now but i dont know the cars harness colorss.

Check out a Chilton's manual for that car.It may be at your local library to view, not sure that they will let you check that out if they have it.Hopefully they have a color copying machine so that you could photo copy the schematic and take that with you.

Q:Are toast - previous owner did a bad amp install on them and there is basically no wire left to use for mine.Is it possible to run a radio power wire/remote wire from the fuse panel back to the radio? If so can i just shove the wire in the fuse holder then stick the fuse back in on top of it?((Fuse 8 is the mustangs radio fuse))

Never wire anything into your fuse box, that will defeat the purpose of having it. You will have to do what's called a hard wire. You will need to run all new wires, which is the safest way to do it, with all proper fusing. A constant +12, a switched +12 and a ground is all you need for the radio to work, and all new speaker wires. If you can find one in a junkyard, you might be able to find a new harness to repair the OEM one, and that would really help you out. Good luck!