Q:have a kenmore dryer with 3 wires now had it will not dry need info on wiring it so it will dry

Here is a picture of the wiring for a 3 wire cord. If this doesn't solve the problem, you may have issues with the receptacle. Just out of curiosity, have you checked the vent hose? If it's clogged with lint, the dryer won't be able to breathe, and therefore won't dry. Good luck.

Q:I'm trying to use a stereo wire instead of a mono wire for an output from a circuit I've built. The problem is, the gold wire has been cut too short, and I'd rather not strip it back any further since I don't have a lot of cord to work with. Since there are three wires (red, white, gold - ground) can I use either the red or the white as output, and the remaining color for ground, or do I have to use the gold cable for the ground and let the remaining wire dangle (taped)?Thanks

They're just wires - you can do what you want with them. You run the risk of forgetting that you've ignored the colour coding though!

Q:I have a 2000 Subaru Outback, and I can get the thing working, but it does not save any of my settings. i know its my accessory wire because the radio will not turn on from any other wire.. soo help please

There are two wires that you must hook up. One is for continuous power so that the settings are saved, the other is for power to the radio. If you had purchased your equipment from Crutchfield, you would have gotten free installation instructions and a wiring harness that would hook directly to your Subaru wiring - saving you a great deal of time and trouble.

Q:do i need a wiring harness or can i use wire crimps and do it w.o on a 2000 blazer 4wd if u think i need it plz tell me thanks

You should always use a wiring harness to install a stereo in a vehicle. Cutting the wires and attempting to hand wire is almost always a bad idea. The wiring harness is pretty cheap ($10-$20) and simplifies the whole procedure. Most of the time, the wiring harness and the head unit have similar colored wiring to aid in quick connections. Also, and more importantly, you can reverse the installation. The plugs will still be there and no cutting and rewiring at all. Remember, the head unit costs $150-$250 bucks, why would you cut corners on the installation kit?

Q:For my braces, the top wire where my two front teeth are, I can push the wire and it sort of bend. I don't know if this is normal or not. Can someone tell me?

Well im 16 and have had my wire braces for 2 years, and all my neighbors have wired braces, but i believe the invisible braces ive seen appear dangerous, like they have somthing on they are tooth. At the least with wired braces everybody knows its braces and no longer some crap you've got on you tooth thats suposed to be invisible.

Q:Where would I get a 2001 wiring diagram for a Silverado chevy truck? I want to re-install the factory stereo that was taken out when I first got it? I have no idea what wire goes where. Thanks a lot.

Car Radio Constant 12V+ Wire: Orange Car Radio Switched 12V+ Wire: Yellow Car Radio Ground Wire: Black Car Radio Illumination Wire: Gray Car Stereo Dimmer Wire: Brown Car Stereo Antenna Trigger: N/A Car Stereo Amp Trigger Wire: N/A Front Speakers Size: 6 1/2″ Front Speakers Location: Doors Left Front Speaker Positive Wire (+): Tan Left Front Speaker Negative Wire (-): Gray Right Front Speaker Positive Wire (+): Light Green Right Front Speaker Negative Wire (-): Dark Green Rear Speakers Size: 4″ x 6″ Rear Speakers Location: Side Pillar Left Rear Speaker Positive Wire (+): Brown Left Rear Speaker Negative Wire (-): Yellow Right Rear Speaker Positive Wire (+): Dark Blue Right Rear Speaker Negative Wire (-): Light Blue

Q:plz answer correctly as soon as possible......why we use stranded 500kV wire?

After AWG 12 or 14, all cable is stranded. The only purpose of stranded wire is to give it flexibility, regardless of voltage or current. .

Q:I bought a single pole dimmer switch to install in my dining room and when I took the old switch out nothing looked right. There are two wires which were joined together by another single wire which was attached to the top screw. There was another single wire (I believe the ground wire) attached to the bottom screw. I disconnected the first two wires and attached them separately to the black wires on the dimmer and attached the ground wires together. It didn't work. I've tired several different times with no luck. I put the wires back the way they were and attached them to the old switch and they no longer work ether. Help! How can I fix this problem? The old wires appear to be a very thick copper covered in black plastic and cloth.....

Dimmer Switch Wiring

Q:The wires I have are: 1 red starter cable, 1 tan wire, 1 ground wire to the engine block, 1 red wire to the battery, and 1 red wire that splits into the fuse and into the junction strip. Really need to know which wires go where on the solenoid.

Red starter wire goes on one of the big lugs, the other big lug gets the wire form the battery and the smaller red wire, the white wire should go on the small lug closest to the battery wire and the black should got to the other small lug. Once you you mount the solenoid on the engine you will be able to tell which side the starter wire and the battery wire are to be placed on the solenoid. The wire from the starter should be only long enough to reach the top lug or the bottom lug just because the way it has to be routed.

Q:i need 175ft of 110 wire how much does it cost?

depends one the guage and copper prices fluctuate daily