Q:Well i bought new speakers for my 92 integra and when i installed them i also wanted to get new speaker wire.how would i go about installing all new wires?would you recommend have circuit city do it or is it not as hard as it looks?

it breaks off because its very thin wire.You need to run new wire.The smallest I would use is 16 gauge wire....14 gauge for the best sound quality. All you need to do is run from your head unit or amp to each speaker.If you have 4 speakers then run 4 wires.EXAMPLE: FRONT CHANNEL LEFT (1) FRONT CHANNEL RIGHT(2) REAR CHANNEL LEFT (3) REAR CHANNEL RIGHT(4) Thats it....Just do your best to conceal the wire under carpet, or along wire mold which is under plasic foot/door strip, on the floor of the vehicle.

Q:I accidently spilled soda all over a bunch of wires and controllers. I cleaned the controllers off and they're not sticky, but what should i do about the wires?

Specify wires.

Q:my dogs have chewed my central air contactor wire.my ac will not cut on. does anyone knows how to replace them and where to buy replacement wires locally( i live in Dallas TX.) i would like to do it myself instead of spending a lot of money.

This should be copper wire and a splice could be made with little risk since the thermostat is a low voltage circuit in most cases. Try the local HVAC contractor for some of the type you need. There are different types ( number of conductors) for different controllers so they need to match. If you just have the HVAC contractor do a fall service on the system they can make the needed repairs and prepare the whole system for the winter. It was probably used a lot this last summer so a service is about due.

Q:im hooking up a air/fuel tomorrow and i need to know what color the wire for the sensor signal is on my rt... i have 4 wires and heres the colors and were they are from. t/w or o/t from c124 b/lbl from c14 and c315 b gound and o/dg from fuse a... need answer thanks

It should be the BLK/ LB wire (although my wiring schematic shows that wire BLK/ GREEN), It will be the only circuit that have a varying voltage between 0-1 volt. Probe the wires with a DVOM and determine which wire has the signal, one wire will supply B+ for the heater, one is heater ground, one is reference supply voltage and one is signal return The signal return is the circuit you need to tap.

Q:wires have been cut and i have 4 wires i dont know what do.what colors are for what?

If your trying to wire a aftermarket radio into your car just go to best buy or any other car audio dealer and buy a wiring harness. It plugs directly into your stock wiring harness and on the opposite side has the correct colors of your aftermarket harness that came with the deck. All you have to do is color match and crimp.

Q:I own a 1990 Toyota 4runner 6cyl, 3L. it had a few performance issues when i bought it. ( just didnt seem to have any power idling at around 200), so before spending money on expensive items, i figured spark plugs, wires, cap and rotor. So i just changed the spark plug wires today, and immediatly the truck was runnin much better idling at 800-1000 , about 5 minutes into driving, the problem started again, i parked the truck, it was idling at 200-300 again, opened the hood saw a bit of smoke coming from one of the wires, so im hoping and assuming it was just smoking because the wire was touching a hot surface, i can hear a bit of a clicking noise that i dont remember hearing before, almost like a spark. what could cause the sudden problem, is it possible the wires could be connected to the wrong spark plugs ( i replaced the old ones one by one, so i know i didnt connect it wrong) any tips would be great

in case you seem on the wires at night you will see them arc on the hours of darkness what form of wires are you employing u want the terrific ones for that motor vehicle what does Toyota say approximately you situation you are able to desire to have yet another situation because of the fact this in no way has been a situation till now what have you ever no longer carried out that could desire to be carried out the race type wires could desire to splendid your situation get them a velocity save and ask for there opinion the radiator sounds love it extremely is stopped up so., while replaced into the final time you flushed the device thoroughly as reported by employing Toyota it extremely is a ninety two and that makes it 15 years old 08 are out now.what form of plugs are you putting interior the engine right here lower back basically the terrific will artwork reliable success

Q:for standard electric wiring, do I cut the white wire or the black wire to not get shocked?

Firstly, the power should be turned off, and secondly, you could get shocked from the active and the neutral. If you break a neutral that has current flowing through it then touch the neutral, you will complete the circuit and get shocked. Just get an electrician, it's cheaper than hospital fees.

Q:Coming from my ceiling I have a black, a grey, 2 white, 2 bare and a red wire. Coming from my ceiling fan/light fixture is a green, black, black with a white stripe and a white wire. How exactly would I go about wiring this? It is a two switch setup without a remote.Thank you in advance.

You have too many wires coming from the ceiling, as it could have done (for separate fan and light control) with a black, red, white, and ground (like 14/3 w/ground romex). Someone apparently added a second run of wire up there. Up at the fan, determine which wire on the fan runs the motor, likely a black fan wire, and which powers the lights (likely a blue fan wire). Connect each to its own switch, preferably using the black you have for the fan, and say the red for the lights, tie the whites together, and the bare together. And the grey just gets ignored. This is gonna be good...

Q:Hi,I'm trying to install a ceiling light with a 3 wire configuration (white, black, ground) into a wire configuration of 4 wires (white, red, black, ground). This is configured for two on/off switches.So far, I have white to white, black to black, and ground to ground with the red capped off. This works with one switch perfectly, however when I hit the other switch, the circuit breaker blows.Please help, and thank you!

captain skalleywag is right. if the switch was originally set up for a fan the red wire is for the light and the black is for the fan. but if it is a 3 way fixture then the wiring is different. are both switches in the same junction box. if they are it is set up for a fan. if there is another switch on an opposite wall it is a three way.

Q:How do you wire a 2 wire smoke detector directly to an alarm (no panel). The terminals are numbered 1,2,3,4 and the instructions say that 1 is for DC+ and 2 is for DC-. How do I wire an alarm so when the detector senses smoke, the alarm goes off? Thank you.

That's DC alarm ,mean you should connected in to 9 volt battery. There are 4 wire alarms that are design for serial alarms. Smoke alarm it's required ,without AC power act and also With AC power act .mean if AC power go off then system will respond on battery power .