Geogrid Layer

Hot Products

Air Diffusers Air Flow Vent for Ceiling

Air diffusers air flow vent for HVAC systerm America Market

4 Way Curved Balde Air Diffusers air conditioner

1-4 way curved blade air vent linear diffusers air flow vent air conditioning

Cruved Blade Square air Vent Diffusers Factory Supplying

China Supplying Air Vent Diffuser HVAC systerm

HVAC Systerm Fresh Air Vent Diffusers Cheap

Air Grille for HVAC systerm And Air Conditioning

Air Flowing Linear Air Diffusers China Supplying

linear bar ceiling air diffuser for air fresh

FAQ

Geothermal pipes are not at all temperatures

Plumbing heat pipe after 2-3 years, the tube wall will produce a lot of accumulated dirt, resulting in inadequate water flow, heat is not enough, heating effect caused a great impact, this time you need to use the warm pipe cleaning equipment to solve the warm pipe Blocking the problem, to warm the pipe dredge commonly used tool is to warm the pipeline dredge machine. In order to clean the pipe, it is necessary to use the correct way to clean, otherwise it will cause unnecessary results.

The pressure to look at the floating spring faint tempered tents touching up in the 1.5 or so, after the opening of the heat will be similar to the heat will see the temperature will rise but it is not put out hot water, and the ground is not hot feeling. But also to open what valve? What is the black valve below the machine? More

Any boiler before starting the machine to pay the water to see if the water pressure gauge pointer is between 1 - 1.5bar. If the water pressure in the above range, open the gas pipe valve, power on, set the machine in the winter position, set the heating temperature, usually the upper limit of the floor heating temperature can be set to 55- -60 degrees Celsius, radiator heating up to 75-85 degrees Celsius (if the radiator is not anti-hot protection, it is best to set the temperature a little lower). After normal ignition do not have to ignore it. Bath: see the water pressure gauge pressure is normal, open the gas valve, power on, set the machine in the summer position (if it is winter, that is set in the winter position), the hot water temperature is set at 42-45 degrees Celsius Between, open the hot water head, until the water temperature is appropriate and stable after you can start bathing. Antifreeze: water pressure gauge pressure is normal, the machine power plug (do not boot), the gas path open (must ensure that the gas source) can be. The above operation applies to Faroe, Haas, Ariston, Bosch, Squirrel, Beretta and other brands of boiler

What are the advantages of home gas boiler?

The advantages of Fiseman's Boiler are: home gas boiler high efficiency, more features, can simultaneously solve the heating and water supply problems; heating the temperature of self-regulation, heating time can also limit their own, With the ax to take good control of the temperature of each room. At the same time the efficiency of its heating system to save gas, heating cycle power consumption is low. Is a good choice

My home is rural, in the floor before the ground should be the first shop or what to do to prepare? And what is its structure, how to coil (and the spacing of the tube), and how to warm into the water pipe and each room of the coil how to connect (not ask what to take together)? My house is a floor tile, would like to shop to warm and tiles do not want to dig out. So I would like to use the sand to do to fill the design and production of the floor, the second is to use the sand cost can be lower and the heat of the heat than the heat more heat

My home is rural, in the floor before the ground should be the first shop or what to do to prepare? And what is its structure, how to coil (and the spacing of the tube), and how to warm into the water pipe and each room of the coil how to connect (not ask what to take together)? My house is a floor tile, would like to shop to warm and tiles do not want to dig out. So I would like to use the sand to do to fill the design and production of the floor, the second is to use the sand cost can be lower and the heat of the heat than the heat more heat...

What is the geothermal decoration process?

First to do the original ground leveling, and then covered with insulation materials, the top of the laying of warm water pipes, and then laying a layer of insulation materials, and then above the mortar leveling

Electric heating furnace in the resistance wire and magnet wire which is a good power saving it

Resistance wire high thermal quality, power saving and durable wire

PE-RTII Oxygen-resistant heating tube custom specifications manufacturers where?

The installation of the warm pipe in the use of metal components to meet, such as switch valves and other metal knot bones buried in the body of the machine, in the plastic pipe during the hot water cycle of these metal parts can easily be corroded, which Will be detrimental to the long-term use of the floor heating system. But the warm system is for a long time to use, and its parts are difficult to replace, which caused the use of heating system inconvenience. Why is hot water circulation in plastic pipes accelerating corrosion of metal parts? After a foreign expert survey concluded that: because the pipe after heating oxygen more easily penetrate the plastic pipe into the hot water, resulting in corrosion of metal parts. Oxygen infiltration is a slow effect, but the corrosion of parts is indeed very obvious, while the heating system is limited to the maintenance and replacement of inconvenient parts, so the impact is not as simple as imagined. Heating plastic pipe is highly resistant to corrosion and high temperature resistance, other materials are difficult to replace, and even if it is possible to replace the metal may not be the role of corrosion, so the key issue is how to solve the oxygen permeation. After research and testing, some foreign experts found that an oxygen-resistant plastic pipe can effectively solve this problem. As the name implies, the oxygen barrier has a good barrier to oxygen permeation, which will greatly reduce the corrosion rate of metal parts. The result of using it is that the average life of the warm system can often be extended, usually over 10 years.

Whether the groove card can be used for heating pipes

Not suitable for the groove in the gasket is rubber material heat resistance is not high long-term thermal environment will cause the gasket aging caused by leakage