Specification of Air Diffuser
Supplying Air Diffusers
-Frame Thickness: 1.0mm /0.8mm
-Any Size be customed
-Powder Coated RAL 9010/9016
HVAC aluminum air conditioner grille
Extruded Aluminum alloy (6063-T5)
Blades in 45°from aluminum profile or as customer’s requirements
30mm as standard or as customer’s requirements
0.8mm, 1.0mm, 1.2mm, 1.5mm or according to the customers’
Powder coated, Anodized , PVDF, Mill finish.
Width x Height, any sizes available
Powder for Finish
Environmental protection and non-toxic, and Color to keep 5 -10 years.
Refer to RAL colors swatch or customized colors available
Drawings designed according to the customers’ requirements
T/T, L/C, PYAPAL, etc.
Usual 15-20 work days for a 40GP container
Bubble wrap + Cartons for FCL, Bubble wrap + Cartons + Wood-box for
Stainless steel security mesh, Aluminum security mesh
Fixing and adjustable installation
Usage of Air Diffuser
The grille is suitable for ceilling sidewall, soffit or cill mounting and may be used for supply or extract applications.
Typical installations include offices, shops, hotels and most commercial or industrial buildings.
Available as standard in white polyester powder coat finish.
Other polyester powder coat finishes are also available as an option.
FAQ of Air Diffuser:
1, What's size do u have for round type diffuser?
A: We have face size from 150mm to 550mm,neck size from 250mm to 400mm聽
2, Do u still have other types ?
A: Yes, we have round diffuser/ rectangle diffuser/ linear grilles/ baseboard diffusers,etc
3, What's the most early delivery time?
A: Within 25 days for each 40'fcl
- Q:How to use the boiler to open a few files
- To warm the boiler to 2-3 files can be. To the use of the boiler: 1, the pressure in the use of the boiler should not be set too high in use, the pressure of the boiler must not be set too high, usually maintained at 1.2-1.5MPa is the right, if the pressure is too large, It will damage the life of the sealing parts, when the pressure is too small will occur the system can not run the normal work, adjust the pressure inside the boiler, as long as the open through the leak valve, the water, in the water on it. 2, do not mix hot water and cold water in daily life, the majority of users are often hot water mixed with cold water use, which is no problem in the water heater, but if the use of warm to the boiler will cause some bad consequences , This is mainly because the warm water boiler is not a direct heating, and only after adding cold water will lead to the cycle to change the pressure inside the system, the boiler sensor will often re-set the system heating mode function, Will cause the boiler to re-use, this will accelerate the aging rate of the boiler. 3, the boiler cleaning and maintenance problems At the end of the day, usually we need to warm the maintenance will be cleaned, the user can operate the first switch into the water, and then increase the pressure to 2, open the drain valve, dirty The water will automatically flow out, so repeatedly operation again and again, until the outflow of water is clean on it, and finally should also open the inlet valve and drain valve, after rinsing, clean, must To add clean water, then adjust the pressure to 1.2-1.5MPa on it.
- Q:Which brand is good to warm the mixer?
- Tsinghua Tongfang
- Q:What is the mixing device in the warmth?
- What is the mixing device in the warmth?...
- Q:To warm or water pipe leakage from the time of the warranty period
- I heard that do not repair.
- Q:What are the common parts of the car heating and cooling system?
- Automotive air conditioning and refrigeration system is mainly composed of compressor, expansion valve, condenser, evaporator and blower, etc., during which the various components between the use of high-pressure rubber pipe and steel pipe connected into a closed system, in the refrigeration system work, the refrigerant will In a different state in this space circulation, and this cycle is divided into four processes: 1, the compression process: the compressor inhalation of the evaporator at the exit of the low temperature and low pressure refrigerant gas, it is compressed into high temperature and high pressure gas Discharge the compressor. 2, the heat process: high temperature and high pressure superheated refrigerant gas into the condenser, due to the pressure and temperature reduction, the refrigerant gas condensed into liquid, and discharge a lot of heat. 3, the throttle process: the temperature and pressure of the refrigerant through the expansion of the device after the expansion of large volume, pressure and temperature of the sharp arrest Cao Ken 丨 old investigation of intestinal fried to decline in the mist (small droplets) discharge expansion device The 4, endothermic process: mist refrigerant liquid into the evaporator, so the refrigerant boiling point is much lower than the evaporator temperature, so the refrigerant liquid evaporated into gas. In the evaporation process a large number of absorption of heat around, and then low-temperature low-pressure refrigerant vapor into the compressor. The above process is repeated for the purpose of reducing the temperature of the air around the evaporator. Automotive air conditioning refrigeration and home air conditioning refrigeration is exactly the same, the need for compressor work, and heating is much simpler, because the car engine after cooling there are about 90 degrees, directly facing the engine blowing is hot air friends.
- Q:System Comparison of Central Air Conditioning Water System
- Specifically, it should be water system and refrigerant system (R22, R410A, etc.). Water system refers to water as a medium, through the water will be the heat and heat transfer to the end, and to adjust the air heat and heat effect of such a way collectively referred to as the water system. The same refrigerant system is through the R22 and other refrigerant to heat and cooling to the end of such a form to achieve the role of regulating the air, known as the refrigerant system.
- Q:Carbon crystal to warm the use of it, what advantages and disadvantages is ah
- Eagle song carbon crystal to warm from the quality to the price, as well as security, aftermarket are very good, you can understand the understanding.
- Q:To warm the warranty period from when to count
- From the installation and control of a good person, the electric to warm for 50 years, 70 years, if that time the company is still the case.
- Q:Water to warm service water heating system as a covert project
- Heating - heating works, through - ventilation works, refers to the delivery, exhaust works; ventilation Wuchu craps tide to see the color of the palace Ji - ventilation works, the same refers to send, exhaust works, air conditioning - air conditioning works, Including heating engineering, refrigeration engineering. Installation sites are the same, to meet the requirements.
- Q:You are registered or heating works basically useless...
- Home wall boiler attention to what the use of boiler concerns...
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range