Transparent Blue PE Protective Film S80-50TB

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT Or LC
Min Order Qty:
10000 Square Meter m²
Supply Capability:
10000 Square Meter Per Month m²/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

General Information of Transparent Blue PE Protective Film S80-50TB 

1. Application: Marble and Porcelain porducts are widely protected by PE film to avoid dirt and scratch during transporation and installation.

2. Transparent color, transparent blue color, black & white color, white color, red color and so on available as per customers' requirements.

3. The choice of surface protective film depends on the surface: material and roughness. Tell us what surface you want to protect and we will recommend proper film to you.

 

Technical Data of Transparent Blue PE Protective Film S80-50TB  

Item Number: S80-50TB

Carrier: PE (polyethylene) film

Thickness: 50micron (0.05mm)

Peel Adhesion: 80g/25mm

Adhesive: solvent acrylic

Color: transparent blue

Temperature Resistance: 60C 48hours no residue

Elongation: ≥250%

Inner Diameter: 3" (76mm)

Length: within 3000meter

Widh: within 1.5meter

Recommended jumbo roll size: 1.0m x 1000m

 

Packing of Transparent Blue PE Protective Film S80-50TB

Wrapped with kraft paper or carton.

 

Remarks of Transparent Blue PE Protective Film S80-50TB

A. The data above are typical results and subject to change without notice.

B. Tolerance: 5%

C. The products should be stored at room temperature and be kept away wet and/or heat source.

D. It is essential, the surface of film must be clean, dry, and free of grease and oil.

E. The users should take test and do trial-application on the above product before coming into application so as to witness and ensure suitability for their special purpose and technique

 Transparent Blue PE Protective Film S80-50TB

 

 Transparent Blue PE Protective Film S80-50TB

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Can non-sticky table tennis racket be coated with protective film?
This is a very simple method. But I assure you it works. Use damp towel to wipe the bat to clean it. And then coat it with protective film when it's still damp.
Q:How to remove the residual glue of the protective film on acrylic board?
You can heat the film with electric hair drier. When it gets soft, peel a cornor of the film and tear it off slowly while heating. You can tear it off quickly this way.
Q:What are the differences between a LCD protective film for laptop and a protective film for mobile phone ?
The functions of a laptop LCD protective film: 1. Ordinary films: Ordinary films only protect the screen from dust and scratch. This kind of films is commonly used and classified into two types--scratch-resistant(a bit more expensive) and non-scratch-resistant. 2. Functional films: this kind of films has better properties of scratch-resistant properties that can be classified into: A. Anti-reflection films, preventing the reflection of light on the screen, work well on some glossy display. Correspondingly they are more expensive than ordinary ones. B. Anti-ultraviolet-radiation films, protecting your eyes, have different technical content. This type of films is colored film --purple or green. But there's no need to mind the color because it's actually transparent when it cover the screen. The color a41 won't show up. And it won't affect the color displayed on the screen. C. Privacy-protective films. After coated with this kind of films, only looking at the screen head-on, or from no more than 30 degrees to sides, people can see the content shown on it clearly. And this kind of films is the most expensive among all.
Q:Why does PE film curl when rolling it after coating?
It may happen if the temperature of equipment is too or glue of high adhesion is applied to fairly thin flim. (The solution is to increase the speed or decrease the temperature.) The adhesion of glue is too high because it's too thick, or the base material is not good, or the stress is too strong when drying the film.(Solution: using the inlet air to press the film from the right side to make it flat and ensure the glue won't fall off.) And if the film you use is composite membrane, when the composite membrane is not composited compeletly, the same problem may occur too. I don't know your coating process, thus all above are the possible reasons that I suppose.
Q:What to do if the sandblasted protective film on marble stele is not adhesive any more?
The reasons may be: 1. If there is oil or water on the surface of the processed stele, the film can't be sticked firmly. 2. Maybe the adhesion of the protective film is not enough. I suggest you try a new film that is more adhesive. We have recieved many similar complaints from our customers. Generally, we will provide them with a variety of protective films for testing.
Q:The ways to remove the protective film on household appliances
I suggest you not to use fire to burn it. You an use a piece of rough cloth or the cloth we use to do the dishes. If you are afraid to scratch the surface, you can slowly wipe it with some toothpaste. If wipe it using steel bush with water, the color of the metal surface may change.
Q:How to define the adhesion degrees of protective film?
At present, there's no such internatinal standards. Each company has its own standards. It's for reference that the adhesion of protective film is usually classified into four degrees which are slight, low, meidium, and high. Generally, 0.02-0.1N refers to slight degree; 0.1-1N,low degree; 1-2N, medium and 2-6N, high. But this is not always the same. It depends on the requirements of themanufacturers.
Q:What kind of material is acrylic protective film made from?
Acrylic protective film can be made from PE materials, PET materials and OPP materials, etc. The materials are the materials used in base film of the protective film. And acrylic is a kind of glue.
Q:The protective film on the surface of raw materials.
Generally speaking, the film is PE (polyethylene) film with single layer structure. It's transparent. Or it is two-layered with composite structure. One of the two layers is BOPP printing film. The other is PET film coated with aluminum. The two kinds of film mentioned above needs to be covered with a layer of PSA before it's used on profiles.If it's difficult to peel down from the profiles, it means the quality of the PSA is not good enough.
Q:What to do if there are some white dots on the protective film coated on high-light product?
Please use protecive film of better quality. The foggy white dots may be generated because the glue reacts with the air.
We are one of the largest manufacturers of adhesive tape and packing machines. With a decade's experience, it has grown to be a mature and important producer in adhesive tape and packing machine industry. Its products sell well both at home and abroad.

1. Manufacturer Overview

Location Guangdong, China
Year Established 2007
Annual Output Value Above US$ 15 Million
Main Markets Southeast Asia; South America; Eastern Europe; North America; Northern Europe; South Asia; Western Europe; Africa; Mid East
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Shenzhen
Export Percentage 10%-20%
No.of Employees in Trade Department 11-50 People
Language Spoken: English; Chinese
b)Factory Information  
Factory Size: Above 5000 square meters
No. of Production Lines Above 10
Contract Manufacturing masking tape, cloth tape, PET tape
Product Price Range Average