Lead Based Paint Encapsulation

Hot Products

Linear Rails

Plug Power Cords

IP65 Waterproof Fluorescent Lamp Fittings

PCS Series Distributed Process Control System from China

Measuring Tools Optical Edge Finder

QCS Proportioning Control System with Advanced Ingredient Test

Wiring Duct

Measuring Tools E.S Optical Edge Finder

Linear Guideway Goods

SPWS Wind Solar Hybrid Charging Controller 200 Watt 300 Watt 600 Watt

FAQ

What are the good brands in Germany of linear guide and screw?

Germany has a lot, some big brands do not pay attention to the Chinese market, so it is difficult to see in the Chinese market!At present China best sales: INA, AM, Rexroth, Schne Berg, KammererIn addition, like Spain and Italy, there are some factories in the production of ball screws, especially Spain's lead screw, the main needle for China's large, long, heavy class screw, it has advantages!

Can I use oil for the guide rail of the machining center?

A machining center, rail oil should be selected with low friction, 1 excellent, can reduce the plastic plating rail caused by the vibration and crawling; 2 high oxidation stability, can be used under high temperature, prolonging the service life of the oil; 3, high viscosity index, the machine starts low viscosity, high temperature can still maintain the proper viscosity, reduce oil leakage; 4, and cutting fluid such as the separation performance of the emulsion has been strengthened, prevent the emulsion away; 5, to prevent the workpiece turns; wear 6, excellent performance.Two, car oil can replace rail oil, but not when the car rail oil oil, automobile oil has several important lubricating oil additive is not common, heat, oxidation, cleaning, dispersion, mobility, and motor oil is a multi-level, such as 10W-40, can be ensured to provide lubrication performance at 25 degrees below zero. The machine tool lubricating oil is usually single stage, such as No. 40, No. 68, if added to the ordinary oil vehicle, tens of kilometers will let the engine scrap.Three, lubricating oil is actually a highly targeted service industry, for different equipment in different environments corresponding to different oil lubrication to guide oil, hot days of the south in general not the same as their high molecular viscosity.Four, recommended: special guide 68# oil processing center, North general 32# or 46# please refer to the specific machine instructions, but absolutely can not use the hydraulic oil, do not lose the greater.

The mechanical guideway acts as a guide Then why are they called rail pairs? What does "deputy" mean?

For example, the lathe, there is a diamond, that is, the wizard role, there is one, that is, sub rail support role

Where is the linear guide?

Widely usedLike some automation industry, machine tool industry, as long as there is a linear transmission place, can be used to get

What are the components of a linear guideway?

Just buy it and we're all sellers

Can the guide rail and screw rod of NC lathe be hydraulic anti-wear 68#?

The two kinds of oil is not the same, the hydraulic oil requirements of anti-oxidation, anti water, anti foam and abrasion resistance, not only can be used in various hydraulic systems, can also be used for medium duty industrial gear (except for worm gear and hypoid gear lubrication). Its ambient temperature is one 10'C-40 'C. This product has good adaptability to nbr.But because of rail oil recycling, the life demand is not high, but the characteristics of start - viscosity is very high, to ensure the accuracy of the sliding guide rail; oil is only applicable to mechanical equipment on their own or around with the guide rail device; in addition for those with hydraulic systems and other mechanical components mixed construction with the equipment, is also very suitable for hydraulic elevator and elevator etc..Ann beauty lubrication technology also has heat transfer oil and hydraulic oil, you can see oh.

What does the DIN- rail installation mean? I see many products mentioned DIN- rail installation. Is DIN a standard or an installation method? Thank you

DIN is the German industrial standard, the use of guide rail is an installation of industrial electrical components, installation of electrical components to support this standard can be easily clamped on the rail without screws, maintenance is also very convenient. The common rail width is 35mm. Some new air switches, such as DZ47-63 series, contactors, CJX1, 2, 8 series, circuit breakers, DZ-108 series, small relays, part of the time relay, etc., have adopted this standard.

SIEMENS PLC rail has 160480530830, four lengths, how to choose? Which is the longest? Is the rail length selected according to the width and quantity of the module? How many modules can be installed in 830? How to quickly select the guide rail?

The 0 frame PLC (power supply, CPU module of the rack) can install 11 module (including power supply, CPU, IM, CP and other modules) even if the length of the guide rail can not continue the rich decoration, must be extended to expand the use of IM module (1 frame). Extension racks can be installed with 9 modules, and if you don't have enough, you can continue using IM and continue to expand.