Lightly Galvanised Iron Wire For Pvc Coated Wire

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Hot Dip Galvanized Steel Wire

(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .

(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .

(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.

(4) Tensile Strength Range

(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.

(6) Packing

(7) Zinc Coating

Meet GB/T 15393 standard.

Q: I'm replacing the door speakers in a 2001 Coupe Camaro with the factory sound system. I needed to know which wire was positive and which was negative so I bought a circuit tester. However, I keep getting the reading that both wires are positive. What could be causing this? I know the circuit tester works because I tested it on the battery terminals and it worked fine.: You cannot use a circuit tester on speaker wires. It is not the correct tester. All you have to do is look at factory speaker it's marked positive and negative.

Q: I want to install an LED and I need to splice into a wire.How exactly do you connect a new wire to an old wire? Do I cut it? Then what? Solder?: Soldering is by far the best method of connecting two wires. You can use the small clamp/connector methods, but they are not very permanent and tend to corrode and lose connection if ever exposed to elements or anything. If you can solder (or even try) -do it.

Q: Anyone know which wire behind the navigation unit is the brake wire? I THINK it's pink, but there are multiple pink wires behind the navigation unit.Thoughts?: Are okorder 's outlander section for a posts on how to disable.

Q: Replaced the old fan in my bathroom (about 10 years old) with a new fan. Trouble is this. The fan and light each work on a seperate bathroom switch. I have two spots to install the wire on the new bathroom fan/light. One for the fan and one for the ligth. However, the wiring has one white, one black, one red and the ground. Anyone know what the red is? Can I just cap it off? According the bathroom fan wiring it says something about connecting red to blue. I am slighty confused. I think it was originally only wired between the white and black. I am not sure if I have to get some extra wire and connect the black and red to the light and the white to the fan? Extra wire is confusing.: The wiring for the original installation had the white wire for a common neutral, and one of the red or black wires for the fan and the other for the light. If your new fixture does not have both a fan and a light, simply use either the red or black, and put a wirenut on the unused wire; you will then have one wall switch that does nothing. If it DOES have both, then one non-white wire goes to the fan, the other to the light, and the white wire goes to both.

Q: I know I am suppose to run the RCA cables and power cables on opposite sides of the car, but which side do I put the speaker wires on, ps I have an amp so I'll be running the wires from my trunk: Red white yes, shouldn't need the toggle. It will turn off with the ignition.

Q: I have 12/3 wire running from the breaker box on a 20 amp breaker that powers a bathroom (2 lights and 2 receptacles). I want to splice into this and run 14/2 wire into the living room to run 6 recessed lights. Is this OK to do?: No, that is against code. Splicing is not allowed nor can you use a lesser gauge on a circuit. To clarify: splicing exposes otherwise insulated wire. The splice has to be done properly such that no wire is exposed, the splice is hardened and this is achieved using a junction box of NEMA appropriate to the installation conditions. A 20A circuit for a bathroom means there is an exhaust fan since a couple of lamps and receptacles do not normally call for that much. That means the circuit has to be able to support 20A and that means the entire circuit. If you extend the circuit using lesser gauge wire than you downgrade the circuit's ability to handle current. This is a fire risk and is a strict no-no.

Q: Is there special speaker wire in order to run 250 watts max rms or will the oem speaker wire in the car be sufficient (did not originally have an amp and is most likely at 50 watts max rms). If I need a special wire for that please let me know what it is called and possibly an example link. Thanks!: most likely the wire pre ran in the car was 16 guage wire which is fairly small id recomend atleast 12G for speakers and 8G for a power wire.

Q: How do I wire with reg 5 wire T-Stat Installing a 2 ton Goodman A/C cond unit to a old Carrier Heat pump AHU with emergency heat strip.: red is your low voltage green is your fan yellow is your cool brown is your com orange is your heat how many wires do you have on the old one should be color to color

Q: ok...all the wires in my quot;atticare encased in this silver metal casing....when i opened a bathroom wall...the wires were also like that.....at the fuse box...they all leave like that........sooooo, can i assume all my wires are encased like that? does that make them pretty safe from rodents chewing? (yup-been watching Billy the Exterminator) why were they done like that? tx for any info....: hi kate in Engand we call it trunking but ime pretty sure its the same stuff, we also cal lit conguate but ime not sure the spell on that is right anyhow we have it white in the uk not sure what your question is but i can only say that its used mainly for protection against animals and more often than not...people hope ive helped danx

Q: A vertical straight wire carrying an upward 14.2 A current exerts an attractive force per unit length of 7.80E-4 N/m on a second parallel wire 7.60 cm away. What is the magnitude of the current that flows in the second wire?: For a current I1 = 14.2 Amperes and radial separation between wires r =0.076 m, the magnetic field at wire 2 is B =0.000037368 Tesla If current I2 = 21 Amperes then the force per meter is F/ΔL =0.000784 Newtons/m hyperphysics.phy-astr.gsu.edu/hba... Goodbye

Send your message to us

*Email

*TEL

*Quantity

*Unit