Q:having a difficult time finding a wire for my remoter starter

The white wire to the coil is the tach wire. If you have the 4.3L,there is a white wire with a black tracer from the ignition control module to the coil. If that doesn't help,on the PCM,in the red connector,terminal 10 is the tach wire from the PCM to the Instrument cluster,this wire is also white.

Q:Do wired controls work better than wireless? My hubby uses wireless and I wonder if wired would transmit quicker?

Wired is better. While there is no lag, the battery wearing out in the middle of a game is kind of annoying. If you move too far away from the console, the wireless will not perform.

Q:How can I stop my cat from chewing wires? He does it all the time, and the wire he ends up being important.

Get yourself a little spray bottle/squirt gun and spray him when he bites on the wires. hopefully that will condition him not to do that....I have 2 cats that both chew on wires and that worked on the first one, but not so much the 2nd yet.

Q:I recently bought a stereo for my truck. What is a good average gage for a ground wire? Speaker wire? Power wire? Last but not least a speaker control (remote) wire? If it helps, I am running a 760 watt pioneer amp on two 12 inch subs. Thanks

1 0 Ofc Wire

Q:From one website I withdraw thru bank wire its 50 dollar fee.What ranges are it for bank wire? Internationally from private person to business.

The bank wire fee varies depending on the individual policies of the bank. Some banks charge for wiring, or receiving. Others charge of international wires. Still others may waive wire fees if you have a special relationship with the bank, such as a Premier Customer, or a senior citizen, etc. Check with your bank.

Q:Just bought a new amp for my truck. The speaker outputs needs to be indiviually wired to the door speakers. Do you splice into the speaker wire or the trucks harness?

ideally you want to wire directly from the amp to the door speakers with new speaker wire but doing this properly requires removing some of the trimming and passing the new wires throughout the car. you can also take the easier route and pass the wires from your amp up under the steering wheel behind the center console and splice them into the existing wires going to the door speakers. as long as the wattage isn't very high the latter shouldn't be a problem. however, if it were up to me i would use new wires and pass them throughout the car, removing the trimmings, etc. this can be somewhat of a pain to do if you have never done it before though.

Q:I have 4 gauge wiring ground and power cables, as well as a smaller guage wiring that is colored grey. I have the amp hooked up to the gound and power, how do I connect the sub to the amp?The subs is a 08 L7 in the kicker truck box wired to 2 ohms. The amp is the Alpine PDX 1.600.

take (i use 12 gauge wire on my sub installs) 16-14 gauge wire and hook up the positive on the amp to the red terminal on the sub and negative to the black one. I'm not really sure what you need exactly

Q:I have a set of two rotating beacon lights on my truck. I would like to wire these directly to the vehicle with an on/off switch. I picked up a two prong toggle switch from autozone, as well as some wire. I'm not sure how I need to do the wiring. I read somewhere about running wire from the fuse box? And how about grounding?

Truck Beacon Lights

Q:subs - dvc 4ohm 2 of them 600wattrms on each wiring it to a 1200 watt amp same brand as sub amp is 1 ohm stable to i wire the subs together and then to the amp a 1ohm? that would give each sub 600 watts right?

The current passing through the wires will cause the wires to heat up if not sufficient guage. Think of the millions of little electrons pushing and shoving back and forth, all this action causes friction on a molecular level and of course we all know friction equals heat. In a bigger guage wire there is more room for the same number of electons. It's really that simple. Use as heavy a guage speaker wire that you can. You will have no signal loss and little heat.

Q:In constructing a large mobile, an artist hangs an aluminium sphere of mass 6kg from a vertical steel wire 0.50m long. On the bottom of the sphere he attaches a similar steel wire, from which hae hangs a brass cube of mass 10kg. How would i calculate the tension in each wire?

The length of the wire is inconsequential unless you're calculating stretch. The tensile force in the upper wire is simply: Fu = 6 + 10 = 16 kg The tensile force in the lower wire is simply: Fl = 10 kg If you want tensile stress, then you need the wire's cross-sectional area.