5000 aluminium sheet in GB3008 production standard

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
4 m.t
Supply Capability:
3000 m.t/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

1.Structure of Product Description

our aluminum sheet is widely used in the field of industrial application, etc.

2. Main features of the product

a.Competitive price

b.Frist-Class Service.

c. Shortest service.

3. Image.

5000 aluminium sheet in GB3008 production standard

 

4. Product detailed sizes:

5. FAQ:

What is the quality standard?

---Usually our standard is GB3880-2006 or others.

What is the width range?

---It is from 1000mm to 2500mm, etc.

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Why can't I melt aluminum?
If you are using tinfoil it is because it is coated with aluminum oxide which has a melting point of 2,000 degrees celcius.
Q:Any difference between aluminum and carbon arrows?
Considering a modern bow at 65 lbs with a carbon shaft arrow and decent broadhead will go clean through a deer, I wouldn't worry about trying to increase penetration, as it's just going to go further into the ground on the other side of the deer.
Q:Aluminium or hi-ten bike?
John and WLE, I hate to disagree... When it comes to bikes in the quality that is presented, the high tensile steel model will be the better one. On lower priced bikes, aluminum frames tend to be heavier than steel due to the low-zoot material. It is a fact that aluminum AS A MATERIAL is half the weight of steel. It is also a fact that it is 1/3 the strength. To make a low end aluminum frame as strong as a steel one, more material has to be added and will be heavier than the steel one. There is a reason that you see more aluminum bikes than steel at places like Walmart. They are cheaper to make. Unless you plan to spend HALF AGAIN what you are looking at for an aluminum bike over a steel model, don't bother... just stay with the steel one.
Q:What is aluminium oxide sheet?
Brief introduction:Advantage:(1) good processing: anodized aluminum decorative strong, moderate hardness, easy bending forming, continuous high-speed, convenient and direct processing into products, no need for complicated surface treatment, greatly shorten the production cycle and reduce production cost.(2) good weather resistance: standard thickness of oxide film (3 m) anodized aluminum plate, indoor use for a long time, no discoloration, no corrosion, no oxidation, no rust. Anodized aluminum oxide film (10 m) can be used outdoors, and can be exposed to sunlight for a long time without discoloration.(3) strong sense: the metal surface of aluminum anodic treatment of high hardness, as gem, scratch resistance, surface is not covered with paint, keep aluminum metal color, highlight the modern sense of metal, improve product quality and added value.(4) high fire resistance: pure metal products, the surface without paint and any chemical substances, 600 degrees high temperature does not burn, does not produce toxic gases, fire protection and environmental protection requirements.(5) strong dirt resistance: no fingerprints, no stain marks, easy cleaning, no corrosion spots.(6) applicability: it is widely used in metal aluminum ceiling, curtain wall board, aluminum plastic panel, fireproof board, honeycomb aluminum plate, aluminum veneer, electrical panel, cabinet panel, furniture panel and so on.
Q:Using thin copper sheets and thin aluminum sheets, respectively, from heat source heat conduction to aluminum heat sink, which kind of efficiency is higher?
Copper is second only to silver as a conductor of heat. The coefficient of thermal conductivity is 398W/mK at room temperature, while aluminum is 236W/mK.The important thing is say three times: please adopt! Please adopt! Please adopt!
Q:Can aluminum plate protect against radiation?
It can only about radiation, and other materials have not heard of this performance.
Q:Could ring-pull can be transformed as aluminum sheet?
Yes, but the ring-pull cans contains fewer aluminum.
Q:how much should the current be adjusted when I use pulse aluminum welding machine to weld 0.7 aluminum sheet?
60-70A current is enough for 0.7 aluminum sheet,the key poiny is that the thin sheet should be bonded with iron sheet or other assistant cooling device when you weld it, or it will be burned through.
Q:how to make aluminum products bright? How to polish or clean the products punch formed by 0.3mm aluminum sheet?
you can try to grind it with magnetic grinder.
Q:Effect of saltwater on Aluminum?
Saltwater is death to aluminum, no matter what your boat dealer says. Be aggresive in monitoring the protective anodes in your engine and on the prop or outdrive - replace when 20% or more eroded. Flushing is good, but eventually your engine will be destroyed by the salt.... Be especially wary in marinas where stray electric currents can cause electrolysis that can destroy the metal parts in your engine in a very short time. Watch zincs carefully if you're in a marina.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range