Q:i have a slightly small mitral valve leak in my heart. my cardiologist say nothing to worry about, but i am not sure. can some one explain if it would eventually lead to some complications?

Mitral valve prolapse is the most common cardiac problem and may affect five to twenty percent of the population. The condition is most common in women, although men are also affected. With MVP, symptoms do not begin before the early teenage years (approximately age 14 in girls and 15 in boys), but adults of any age may be affected. MVP tends to run in families, so those with blood relatives with MVP have a greater chance of also having the condition. If a person has mild MVP, he/she needs no restriction of exercise. But if the MVP is big, then it is a different thing. Because, though complications in this condition are very less, people who suffer from this condition have to take extreme care. In case of large MVP, you may have to cut down on your physical activity, have a surgery and may be put you on medications like beta blockers. If the valve is truly defective (not just 'prolapsed'), it is serious. Unfortunately, doctors have mistaken a 'differently shaped' mitral valve as a disease in itself. And this is where the non-disease comes in. In simple terms, a mitral valve that appears prolapsed is usually normal. It still is not clear to experts why some mitral valves appear prolapsed and allow some blood leakage backwards. I have an answer for that phenomenon, but the important point is that the disease is a non-disease.

Q:The difference between butterfly valve d71x_10s and d341s-10

Before distinguishing between the two, you must first read the identification of the valve type:D stands for butterfly valves,3 means that the worm gear is connected and the drive does not indicate the handle7 and 4 indicate pipe to clamp connection, pipe flange connection, respectively1 means single eccentric, that is, the stem is not in the center of the butterfly plateThe former S indicates the material name of the valve body - plastic, X means sealing and the lining material is rubberThe latter S indicates the sealing lining material code ---- plastic, and the valve body is cast iron.10 means stress.

Q:What's the difference between butterfly valves and check valves?

Butterfly valve is manual, only switch function.The check valve is an automatic valve, which prevents backflow of the pipe medium.

Q:What's the material of the butterfly valve seat?

The seating material shall meet the following criteria:1) fluid compatibility, including expansion, hardness loss, permeability, and degradation;2) hardness;3) permanent deformation;4) the degree of recovery after load removal;5) pull in and compressive strength;6) deformation before fracture;7) modulus of elasticity.

Q:Who can give me a download UG butterfly valve, needle valve, diaphragm valve standard model address, Japanese standard, American Standard.

Support many 3D CAD format, such as the commonly used UG, Pro/E, SolidWorks......As for the butterfly you said, don't post the link up, the standard JIS, American Standard ANSI, German standard DIN are.You use Baidu Search "LinkAble PARTcommunity", after the open registration, CAD format, such as UG, ASAHI and then to find the manufacturer home page, which is the valve, you said the Japanese standard, German standard, American Standard valve basically all.

Q:Butterfly valves are widely used in 2.0MPa below the pressure and temperature of not more than 200 degrees of various media, right?

First of all, is not the butterfly valve butterfly valve.Butterfly valve in the valve around the fixed axis rotating valve, called butterfly valve.1., as a sealed butterfly valve, it has been developed rapidly since the appearance of synthetic rubber, so it is a new type of shut-off valve. In our country until 1980s, the main role of butterfly valves in low-pressure valves, valve seat using synthetic rubber, by 90s, hard seal "metal seal" butterfly valve to rapid development. There are a number of valve factory can produce steady pressure metal seal butterfly valve, butterfly valve shall be shipped to a broader area.2. butterfly valves can transport and control the medium with water, condensed water, recycled water, sewage, sea water, air, gas, liquid gas, dry powder, mud, fruit pulp and a mixture of suspended solids.The domestic butterfly valve parameters are as follows:Nominal pressure: PN0.25 - 4.0MPaNominal diameter: DN100 - 3000mmWorking temperature: less than or equal to 425 DEG C

Q:can't locate freon intake valve for 03 jaguar an was wondering were it is located at

If it has one it should be located on the smaller line near the AC compressor.

Q:What is the effect of nylon coating on butterfly valve plate? Thank you

Mainly media will not be contaminated by rust on the body, you should say that the central soft sealing butterfly valve, the central valve is generally cast steel or cast iron material, so useNylon coatingLining up. There are soft seals, sealing performance is relatively high

Q:What's the difference between D71X-16 and D71H-16 butterfly valves?

First, model D71X model means that, on behalf of 7 representative D butterfly valve, butterfly valve connection form for clamp connections, 1 straight, X represents the seal in the form of soft sealing, the sealing surface usually NBR H metal seal is usually 2Cr13 16 represents the pressure of 16 kg pressure weldingJin Ya valve is the production of hard sealing butterfly valve or soft sealing butterfly valve line leader, what problems can ask their units, technicians will answer for you

Q:What's the difference between cut-off valve, gate valve and butterfly valve? What's the difference in the working principle?

Stop valve is closed parts (valve) moving along the centerline of the valve seat, the valve stem to open or close the trip is relatively short, but very reliable cut off function, and because changes in the valve seat and the valve stroke is proportional to the amount of adjustment is also very suitable for convection.Check valve: also known as counter flow valve, check valve, back pressure valve or one-way valve, such valves are dependent on the flow of the pipeline itself flow force and automatically open and close, belonging to an automatic valveButterfly valve: it is a kind of valve which uses disc type opening and closing parts to turn back and forth about 90 degrees to open, close and adjust the passage of fluidGate valve is closed parts (RAM) along the vertical axis of the mobile channel valve in the pipeline, used primarily as a medium cut that open and close, generally do not have to do with traffic regulation, it can be used for low temperature and low pressure can also apply to high temperature and high pressure, and according to the different valve material is different in various media. The valve, the valve is the most widely used.