Q:After the pile into the warehouse after the fast press line, the steering wheel how to amend?

Makes sense.

Q:two fly wheels are connected by a belt. the small one has a radius 5cm and the small one has a radius of 2 cm.if the large wheel rotates 150 degrees then how many radians does the small wheel rotate?

Arc length radius x angle in radians 150 degrees 150 pi / 180 radians 5/6 pi radians Because of the belt, both wheels move by the same arc length. If the small wheel angle is a, then 5 x 5/6 pi 2 a a 25/12 pi radians 6.54 radians

Q:* 7 Wheels refers to a Japanese Clan Name* 7 shichi / nana / nana-tsu / nano* Wheel rin / wa_______________I‘m guessing it would look something like this? :Romaji : NanaWaKana : 七輪

Easy to maneuver, fairly bendable (up to 3 degree's at a min of 300', that's actually very good), chemical wise it is safe with water (wont rust, wont chip, water is drinkable when it goes through it), compared to other metals it's cheap. Copper is becoming more expensive compared to plastics and other mostly man made things so they are switching to something that's closer to plastic. Something more common is High Density Poly Ethel (HDPE). It's what just about everyone has switched to. Worked for a civil engineering place as a drafter (had to look up material costs).

Q:Ladder group, wheel group, etc. What are the differences, purpose, precautions?

This is not only time-saving, but also for the promotion of muscle endurance is also good.

Q:So I just got my car back from the shop. 3 months ago the deal told me the rear axel was leaking grease. I took it to a mechanic (hoping for a cheaper price) and told him what was wrong. My car would squeak on occasion and one night as I was driving I heard a metal on metal scraping noise. I figured it was the lack of grease in the rear axel so I decided to get it looked at. The mechanic said I was fine on my rear axel but replaced the seals on my transmission. I started hearing the same noise again today as I was going to park it. I‘m thinking it might be the wheel bearing but I‘m not sure. If they were going bad, would they always make the noise? I drove it around quite a bit in between hearing the sound. Help!

The wheel bearings make a grinding noise when they go bad. You can check the wheels by lifting the car and trying to move the wheels back and forth, not around. If you notice any movement the bearing is bad.

Q:I want to change the front wheel of Micro Sprite Scooter to 100m wheelthe front wheel of Micro sprite is 120m.do u think it will fit?

Do you mean 100mm? You can measure it with a ruler w/milimeters on it, just measure the width between the outer edges (where the tire bead would lay) If you are talking mm then a 120 mm rim would most likey not fit, you must take into consideration the area needed for the front fender and forks. The tire would rub on them. if your going smaller, there should be no prob.

Q:I‘m going to be getting a silent spinner wheel, I thinkShould I get two 4.5 wheels or one 6.5 wheel? I also heard mesh wheels are good for mice because since mice or very fast and agile, they can step on every one of the little bars. I heard that mesh wheels are also good if you have more then one mouse because if the first mouse goes too fast, then the second one can grip the wheel and hold on so she doesn‘t fall off. So should I get a silent spinner or a mesh wheel? If I get the mesh one, I‘ll be getting the 5.75 wheel:)

Although many people say mesh wheels can get a mouse's tail stuck, I've never experienced it and personally prefer the mesh. If you do choose the silent spinner, which will also be fine, get the 4.5 wheel. It will probably cost less and will have plenty of room to fit one mouse. My two mice have a really small wheel and have no problem using it at the same time. Hope I helped!

Q:i recently bought a somewhat cheap aftermarket steering wheel and hub adapter. i took it out for a test drive and found out its really hard to steer! are all the aftermarket steering wheels like this, or will the more expensive/ name brand ones be alot better? (sparco, momo, etc.)thanks ahead of time!

It is that way because there is a loose nut behind the wheel

Q:I‘m thinking of getting a Syrian hamster but I don‘t know which wheel to get.i‘ve found a website that has the comfort wheel and the wodent wheel the comfort wheel is about half the price of the other one but I don‘t know which one to get can anyone help me in which one i should get.

The wodent wheel is apparently very good, personally I recommend the 11 Trixie wheel. It doesn't arch the Syrians back so it's perfect for them. It's also very quiet!

Q:change front wheel bearing on rear wheel drive car, 1994 mercury cougar xr7

use a pair of channel locks.pull the round cap in the middle take out the cotter pin and remove the nutjacked up of course give the wheel a tap out comes the outer wheel bearing take rotor off use a long drift and punch our rear wheel bearong and seal.get new seal and bearings pack with wheel bearing grease .there are two races the bearing rides on.it's simpl;e to remove but ask where you buy the bearings as they are a setpu it all back together opposite correct torque on th nut .away you goeasy and no press required