stainless steel hose nipple
high quality competitive price
silicasol shell technology
stainless steel hose nipple
suitable medium:Petroleum, natural gas, chemical industry, water and electricity, architecture and boiler piping system etc
- Q:How did the manuel typewriter work, what were some of the most popular modules and brands?
- If a satellite is withing 61,500 km of the moon, then the moon's gravity is stronger that the Earth's. Certainly, any satellite within 30,000 km is going to stay orbiting the moon.
- Q:Do patients wearing a heart pace makers need to stay away from microwave ovens?
- $50.00 for a Dewar Flask that size is not going to happen. Reposting the same question over and over is not going to change that.
- Q:home window and door alarms?
- Copper is the way to go. It's the easiest to put it. It doesn't build up with calcification and won't corrode. It's extremely easy to work with using no threads.
- Q:How to identify the pipe joint thread quickly and accurately?
- 1 use a thread gauge to check the gauge of the pipe joint, which is the most accurate.2, you can also use special tools, taps (for female pipe joints) and wrench (for pipe fittings), which is a tool for making pipe joints. Try it on and see if it's easy to screw in. If it is easy to screw in, you can determine the specifications of the unknown pipe thread according to the specifications of the known taps and wrench marks.
- Q:Why are the sleeve joint leaks?
- The hardness of the clamping edge is not enough, or the steel pipe is too hard. After the assembly, the clamping edge can not cut into the pipe wall to form a seal. Solve: replace the qualified card sleeve.The end face of the steel pipe is not vertical or clean, which hinders the proper installation of the pipe. Solution: carefully clean the end face before installation.The joint body and the steel with different axis, leading to the assembly is not correct, extrusion is not tight, at this time can be found in the card set apart and cut the pipe wall, left the marks of a single whole foot ring groove. Solution: when installing, make sure the joint is coaxial with the steel symbol.
- Q:What is pressing type pipe joint
- If necessary, I will send you the connector type and specifications
- Q:Hydraulic pipe quick coupling principle of hydraulic pipe joint
- Quick change joint, one is with one-way valve, and the other is without one-way valve. The application with a one-way valve, a one-way valve end is connected with the gas source, when the check valve closes automatically when connected to a one-way valve open end of the thimble. Self locking is the use of steel balls embedded in the groove, while the "cone - cylinder" sleeve to lock the ball.Type, type, structure diagram, characteristic table and standard number of pipe joint, welded pipe joint is welded by pipe and pipe. The sealing surface of the O sealing ring is sealed between the joint body and the pipe. The utility model has the advantages of simple structure, easy fabrication, good tightness and low requirement for the dimension precision of the pipe. High welding quality, inconvenient assembly and disassembly. The working pressure can reach 31.5MPa and the working temperature is -25 to 80 degrees. It is suitable for the piping system with oil as the medium. Table 6~14The JB966 ~ 1003-1977 card sleeve pipe joint is jammed and clamped by the deformation of the clamping sleeve. The utility model has the advantages of advanced structure, good performance, light weight, small size and convenient operation, and is widely used in the hydraulic system. Working pressure up to 31.5MPa, requiring high dimensional accuracy of the pipe, cold drawn steel pipe is required. The card sleeve is also of high accuracy. Piping systems for oil, gas and general corrosive media 15~26
- Q:Hydraulic hose connector size 20As shown in Figure six, the angle is 71mm to the edge, 80mm to the diagonal, approximately 34mm higher
- Two. Metric general threads1. metric screw thread with a capital M, tooth type angle 2 degrees =60 (alpha tooth type half angle);2. metric ordinary thread by pitch, coarse teeth, ordinary thread and fine teeth, two kinds of ordinary thread;2.1. coarse tooth ordinary thread mark generally does not indicate the pitch, such as M20 means coarse thread; fine tooth thread mark must indicate the pitch, such as M30 * 1.5 for fine tooth thread, in which pitch is 22.214.171.124. common thread is used for the connection and fastening between the mechanical parts, and the general thread connection is mainly made of coarse thread. The thread strength of the fine tooth thread is slightly higher than that of the same nominal diameter, and the self-locking performance is better.Mark 3. metric screw thread: M20-6H, M20 * 1.5LH-6g-40, where M represents a common thread metric, 20 nominal diameter thread is 20mm, 1.5 pitch, LH said, 6G 6H left, said thread precision grade, precision grade of internal thread uppercase, lowercase precision grade of said external thread, 40 screwing length.
- Q:The difference between threaded pipe joint and grooved pipe joint
- It is divided into: the wire connection and wire connection. If the two are double wire connection is in need of a two double wire transition; if between the two are: double wire connection is in need of a two double wire transition; if the two just one male and one female, and the thread and facilities, it is directly screwed on it is good.
- Q:A fire hose held near the ground shoots water at a speed of 6.7 m/s.?
- Channel lock pliers. There is a picture in the link. Al
For the recent ten years, our company has devoted ourselves to the production and development of stainless steel precision casting products. With the spirit of "cast the excellent and reliable products by our sincere attitude, hard working and good standing", we warmly welcome friends from at home and abroad to visit our company.
1. Manufacturer Overview
|Annual Output Value
||US$2.5 Million - US$5 Million
||30.00% North America
15.00% Southeast Asia
10.00% South America
10.00% Mid East
10.00% Western Europe
10.00% Central America
10.00% Domestic Market
5.00% Northern Europe
||50 strong foundry industry;GOLD MEDAL CASTING;GOLD MEDAL CASTING;GOLD MEDAL CASTING
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||Tianjin Port,Shanghai Port,as the customers' requirements
||91% - 100%
|No.of Employees in Trade Department
||English, Chinese, Arabic
||5,000-10,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range