Product Description:
SKCBS1600 BAND SAW
1>Working Range:less than or equal to 1600mm
2>Vcc:380V,50Hz
3>Cutting Angle:0-67.5
4> wEIGHT :7000kg
Application:
Suitable for cutting pipes according to dpecified angle and dimension while making an elbow,tee or cross, which lowest the material waete and improve the welding efficiency.
Features:
1>Cutting angle 0-67.5°.
2>Self inspecion and stop of the machine in case of saw blade breaks enables to guarantee operator's safty.
3>Applied to solid pipes or structured wall pipes made of themrmoplastic such as PE and PP,and also other pipes and fittings made of non-metal materials.
4>Reliability,lower noisy,easy to handle.
5>Complies with 98/37 and 73/23 EEC standards.
Technical Specifications:
Working Ranges: | SKCBS1600≤1600mm |
Cutting Angle: | 0-67.5° |
Saw Power: | 4000W |
Hydraulic Unit Power: | 1500/750W |
Working Voltage: | 380V 50Hz |
Line Speed: | 0-200m/min |
Feed Speed: | Adjustable |
Weight: | 7000kg |
- Q:Will the frame beam longitudinal stress, steel E55 electrode, the power requirements of the welding machine?
- Specific requirements for you to see what the problem of choosing motor electrode, are required, what do you use for electrode current and what specific requirements, the electrode that has will help you choose what what current high current motor
- Q:If the welding rod does not release in time, will the electric clamp affect the welding machine?
- The electrode and the weldment are in contact with each other and will burn in the absence of arcing, which is equivalent to the two side short circuit and the current is infinite.When the coil is insulated and aging, the rated voltage is too large, the electric welder will be burnt out!Under normal circumstances, the two side burned out, overload, that is, his output power is greater than his rated power!
- Q:Why are the alternating current welding machine and the welding machine considered in the quota?
- The two welding machines are used in different places
- Q:How long does it take for electroslag welding machine to butt a steel joint? Which kind of butt welding method is adopted for steel butt joint on construction site? Which welding machine is the best?
- One of the joints of electroslag welding is about 5 minutes.The site is usually: vertical (pillar) electroslag welding; transverse (Liang Ban) arc welding.There are flash butt welding, welding quality is often not high, and welding equipment difficult upstairs homework, not often used.
- Q:How to choose parameters of flash butt welding machine
- Selection of welding parameters, we should consider the current when welding, the maximum carrying capacity of the transformer, and then we can choose the parameters of the welding machine according to our own work. Basically, the technical parameters of the welder are the same
- Q:Field steel needs butt welding and has three power supply butt welding machines. We must have three items on the spot
- As far as I know, welding machines are all two FireWire, and three items have not been heard yet.... I make wall screws
- Q:UN1-125 type butt welding machine working principle, who knows, I encountered the problem is welding power, but can not work, who can give I I answer?
- Bad contact at the output stage
- Q:Saw welding is the use of welding machine, I do not know how good tempering, tempering to what extent, I always break the interface
- First of all, the premise is that your welding should conform to the standard, and then the annealing. The detailed operation procedures are as follows: 1. Adjust the welding contact space to 18-20 mm wide. Then put the saw on it and press it tightly. Two 、 adjust the current to the minimum. Three, quick click switch. Four. Observe the weld until it is slightly aglow. So far, the annealing is complete. There is a problem to go "woodworking belt saw blade" stick to me
- Q:What is the difference between an electric welding machine and a butt welding machine?
- The welding machine is the same as the butt welding machine in principleThe power of an electric welder is continuous. There is a solder in it. The heat generated by the two electrodes causes the solder to melt and the current has passedThe power of the welding machine is small, it is a short time work, in the two electrodes encountered a moment, the current generated, and then there is no
- Q:What does a flash butt welder have in addition to the transformer?
- SCR, relevant welding, and some circuit board, CNC equipment, some pressure! Quite a lot！
Our company has always been committed to the research, development and production of plastic pipe welding equipment. Its plastic pipe welding equipment has obtained dozens of international patents, enjoying an internationally high reputation due to high quality, exquisite appearance, excellent performance and perfect after-sales service. We are convinced that our unremitting efforts and persistent pursuit will bring us a more bright future while serving world plastic pipe welding equipment industry.
1. Manufacturer Overview |
| Location |
Jiangsu,China (Mainland) |
| Year Established |
2010 |
| Annual Output Value |
|
| Main Markets |
20.00% Western Europe
20.00% Mid East
20.00% South America
20.00% North America
10.00% Northern Europe
9.00% Southeast Asia
1.00% Central America |
| Company Certifications |
|
2. Manufacturer Certificates |
| a) Certification Name |
|
| Range |
|
| Reference |
|
| Validity Period |
|
3. Manufacturer Capability |
| a)Trade Capacity |
|
| Nearest Port |
|
| Export Percentage |
61% - 70% |
| No.of Employees in Trade Department |
|
| Language Spoken: |
|
| b)Factory Information |
|
| Factory Size: |
10,000-30,000 square meters |
| No. of Production Lines |
7 |
| Contract Manufacturing |
OEM Service Offered Design Service Offered Buyer Label Offered |
| Product Price Range |
|
