Pe Pipe Electrofusion Welding Machine
1. type:PE pipe electrofusion welding machine
2.welding range : 20~315mm
3. input power: 220V 50HZ
♦ Our eletrofusion welding machine adopt RMS control, main suitable for connection of PE pipes and fittings which are used for natural gas or water supply. It is the perfect equipment for manufacturers or construction units of pipes and fittings.
♦ High brightness LCD display. Chinese/English operation. Friendly interface for human and machine
♦ Wide power supply and voltage input, fully suitable for spot electric network wave
♦ High accurate power , time controlling. Ensure welding quality
♦Huge storage capacity for welding datum, easy way to enter welding parameters
♦ compact design, small volume and light weight
48V±10%,220V±20% or 380V±20%
Data record times
Power constant precision
Time control precision
Temperature measurement precision
See the fault sheet
- Q:Who can tell me the principle of flash butt welding machine?
- Principle:In this stage, the power supply is first connected and the two workpiece face is slightly contacted, so that a lot of contact points are formed. When the current through the contact point, melting into liquid metal connected to the two end of the lintel. Due to high current density of liquid in the liquid metal lintel, evaporation, blasting in the lintel lintel. With the moving clamp slowly advancing, lintel has been produced and blasting. Liquid metal particles are ejected continuously from the interface under the influence of vapor pressure and electromagnetic force. Spark of sparks - flash.In the flash process, the workpiece is gradually shortened, and the end temperature is gradually increased. With the increase of temperature at the end of the lintel blasting will accelerate the speed and propulsive speed clamp must also increase gradually. Before the end of the flash process, the entire end of the workpiece must be made of a liquid metal layer, and at a certain depth, the metal reaches the plastic deformation temperature.In the flash stage at the end of the top exert enough pressure on the workpiece immediately, the interface gap decreases rapidly to stop blasting into the lintel, upsetting stage. Upsetting is the role of the seal clearance and left end surface of the liquid metal lintel after blasting crater, liquid metal and oxide inclusions and extrusion surface, the plastic metal clean close contact, and the joint area of plastic deformation, in order to promote the recrystallization in grain, forming a common and strong the joint.
- Q:What kind of power supply is common for welding machines used on site?
- The power of welding machine is about 15kw
- Q:150KW what size cables are used for flash butt welding machines?
- Some 50 square flash welding line, 1.5 square wire bending machine and machine fault is enough, but consider other problems with 2.5 square line. 16 square cable for electric welder.
- Q:Leakage switch operating current 30mA can not meet the use of steel butt welder, how should I do?
- It is best to replace one, simply did not make it go without
- Q:What is the use of electroslag pressure welding machines, alternating current welding machines and flash butt welding machines?
- Agree with the upstairs, as well as mechanical connections, mechanical connections, more than 18 of the province's steel, reasonable price, can be used for Liang Jizhu, foundation and other components
- Q:Why are the alternating current welding machine and the welding machine considered in the quota?
- According to the actual construction machinery required for consideration, because steel construction, electric welding machine is generally used in lapping of bars and other parts, the welder is mainly directly butt joints of large diameter bar, not a waste of lap length, so considering the quota.
- Q:When welding, the machine needs water to cool it
- It takes a look at the power of the welding machine and the heat, and then judge whether the water cooling is required, usually for welding and heating power of large amount of words, recommend the use of cold water cooling machine, such as 5KW & CW-5200 chiller for cooling water cooling on welding machine can, in order to ensure the normal operation of the machine.
- Q:How much square is the voltage of the 100 kW butt welder with 380V?
- 95 square 60KW GB, no 100 specifications
- Q:How many KW generators will be needed for the steel bar welding machine used in the railway engineering construction?
- At least 300
- Q:What is the difference between an electric welding machine and a butt welding machine?
- Electric welding machine is used in the two side of relatively high pressure (more than 60V) and large current to the electrode as welding materials arc welding; while the welder is used in two times of low voltage and large current (10V) with 2 pieces of metal on the electric arc welding or from the upper and lower welding head 2 pieces of iron with high current through the self pressure contact welding.
Our factory has a senior technical team engaged in plastic pipe welding equipment research and design. The guideline of our enterprise is "user's need is our pursuit; the product quality is the lifeline of our enterprise". Our aim is to be a world-famous factory.
Our products include TGH multi-angle welding machines, DQJ multi-angle cutting machines and RDH hot-melt welding machines.
1. Manufacturer Overview
|Annual Output Value
||40.00% Domestic Market
15.00% Mid East
10.00% South Asia
10.00% Southeast Asia
10.00% South America
5.00% Eastern Asia
5.00% North America
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||41% - 50%
|No.of Employees in Trade Department
||English, Chinese, Spanish, Portuguese, Russian, Korean
||1,000-3,000 square meters
|No. of Production Lines
||Design Service Offered Buyer Label Offered
|Product Price Range