Q:really though, I think I'd have to run outside naked and if my cellphone was not in reach, use a neighbor's phone to dial 911. Talk about a rush. now the people I know cant even say the only thing I own are the clothes on my back. Is this the right thing to do, to not grab anything on your way out?

rubber cement of course. but, you need to prepare your surfaces. wash with soapy water, rinse and dry completely. now rough up the area to be glued with sandpaper or a little grater(often included with the glue). you should probably stretch your rubber if it will be normally stretched.

Q:What are the specifications and models of hydraulic pipe fittings?

Mechanical design manual fourth volumes, hydraulic pipe joints are there?. You go check it out,.

Q:What joints do nylon hard tubes work on?

(two) clamp sleeve type pipe joint;Application: sealing pipe joint oil, water, gas and other non corrosive or corrosive medium, with plastic pipe specifications are flexible, and pipeline connection, has the characteristics of reliable connection, good sealing performance, so it is widely used in oil refining, chemical industry, light industry, textile, metallurgy, national defense, aviation, ship the system is suitable for all kinds of hydraulic transmission; mechanical engineering, machine tools and other equipment pipeline. Sleeve type pipe fittings manufacture standard following fifteen kinds:1, card sleeve end through pipe joint (GB/T 3733-2008)2, sleeve type cone thread straight pipe joint (GB/T 3734-2008)3, card sleeve type end through long pipe joint (GB/T 3735-2008)4, long taper pipe thread joint (GB/T 3736-2008)5, card sleeve straight through pipe joint (GB/T 3737-2008)

Q:When I put a DVD, CD or anything into the drive, it sounds like it spins for a moment and then stops. On the My Computer it wont even register that I put something in it. My MediaSmart also says there is no disc when in fact there is one. The button to open the drive works perfectly. What could have happened in the past few days to cause this?

surprising to know that you are not able get from any of the stores you mentioned.try from a big town nearby.

Q:I am working on a project with unbuilding a LASER lightshow-style projector. it is a class III b laser rating, with the following specifications: Wavelength/power: 532nm / 50mw (Green), 650nm / 100mw(Red) I may end up accidentally looking directly at the beam (although I certainly will be trying not too) I understand this laser is capable of seriously damaging my eyes if they are unprotected, so what eyewear should I use for these wavelengths? or would a weilding mask work just fine? that s about all I ve got in terms of serious eye protection, though i may just go buy something else if i know what to get!! thank you so much for your help guys!!!

The easiest way to get it right the first time is break off a piece of the pipe and take it into the store. Someone there will make sure you buy the right size fitting. Don't use teflon.

Q:How are the sleeve couplings joined?

The clamping ring is inserted into the outer wall of the steel tube by the action of the nut and the main body so as to form a seal

Q:Want to know how many types, and each type is best to bring pictures

Mechanical design manual fourth volume hydraulic pipe joint that part has detailed introduction and each installation size, and comes with the picture Oh, a glance will understand, hope to adopt Oh!

Q:Joe kittenger sky dived at 102 000 feet in 1960, but that was only in the second part of the atmosphere. Of course if you were wereing a pressure suit would it be possible

Is the pipe PVC, or CPVC? It is important to know, since PVC is not made for hot water! The outside diameter of PVC is larger than CPVC, so different fittings are required. I would think it is CPVC pipe, so the outside diameter is 5/8, therefore 5/8 compression angle stops will work. If the pipes are PVC, then you need glue on male adapters, and female threaded angle stops. I suggest getting the branch side of the valves to be 3/8 compression joints also. These are easier to work with, and more readily available, than flare fittings. If your pipes are PVC, I highly suggest replacing them with heat resistant pipe, or you will wake up some morning with a house full of water, after the pipe melts. Good luck!

Q:I just had a new mobile home (1988) new to me I should sayanyway I just got the power on before that somebody came and inspected the wires and allwhen I turn on my lights they glow florescent orange in every room its not the bulbs its like its trying to light up but doesn't. Then if I turn my heat on it smells like somethings burning then my smoke detectors go off. Then there's a painted peice of a wall in front of my water heater after turning the power on after a few minutes there's a weird smell like wet paint combing from that. Any suggestions?

Use fire to enlarge the diameter of the PVC.

Q:1/8 the trachea needs an outside diameter of the trachea

1/8, you can transfer 4, 6, 8, and 10.SMC pipe connections, please refer to "SMC pneumatic service network""