Graphite Electrodes for Water Electrolysis - Big Dia. Super Quality
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 400 m.t.
- Supply Capability:
- 5000 m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Specifications
.UHP Graphite Electrodes
.HP Graphite Electrodes
.RP Graphite Electrodes
2. Introduction of Graphite Electrodes
G-High Graphite Electrodes have the properties of superior electric conductivity and chemical stability, high mechanical strengt
G-High Graphite Electrodes are made from Petroleum Coke and Needle Coke, using Coal Tar Pitch as agglutinant, produced through the process of calcining, mixing, kneading, compressing, roasting, graphitization and machining, etc.
G-High Graphite Electrodes have the properties of superior electric conductivity and chemical stability, high mechanical strength, less impurity, seismic performance in high temperature. G-High Graphite Electrodes are mainly used for steel-making in electric furnaces, mineral hot furnaces and electric resistance furnaces.
Graphite Electrodes conduct electric current into the furnace. Electric current produces arc in the smelting district, when the temperature increases to about 2000°C, smelting begins. Our series of Graphite Electrodes are applicable to the common furnaces and high power furnaces with high voltage and short arc. G-High Graphite Electrodes are classified into three classes.
NP Graphite Electrodes: mainly used in common power electric ovens for smelting steel, smelting silicon and smelting yellow phosphorus;
HP Graphite Electrodes: mainly used in high power electric ovens for smelting steel;
UHP Graphite Electrodes: mainly used in ultra high power electric ovens for smelting steel.
Graphite electrode(please check form)
Graphite nipple
3. Details
Specification | Specific Resistance (μΩ.m) | Young's Modulus (Gpa) | Flexural Srength (Mpa) | Bulk Density (g/cm 3 ) | Ash Content (%) | Coefficient of thermal expansion ( 100-600 C)10 -6 1/C | ||||||
(max) | (min) | (max) | ||||||||||
Electrode | Nipple | Electrode | Nipple | Electrode | Nipple | Electrode | Nipple | Electrode | Nipple | |||
Regular power | 200-350 | 8.5 | 7.5 | 9.3 | 13.7 | 9.8 | 15.0 | 1.55 | 1.72 | 0.3 | 2.9 | 2.8 |
400-500 | 8.5 | 7.5 | 9.3 | 13.7 | 6.4 | 15.0 | 1.53 | 1.72 | 2.9 | 2.8 | ||
CTL Resistant Oxidation Electrode | 200-350 | 8.0 | 7.5 | 9.3 | 13.7 | 10.0 | 15.0 | 1.56 | 1.72 | 0.3 | 2.9 | 2.8 |
400-500 | 8.0 | 7.5 | 9.3 | 13.7 | 7.0 | 15.0 | 1.54 | 1.72 | 2.9 | 2.8 | ||
High Power | 200-500 | 6.5 | 5.5 | 12.0 | 16.0 | 12.0 | 18.0 | 1.63 | 1.74 | 0.2 | 2.4 | 2.2 |
Supper High Power | 250-500 | 6.0 | 4.8 | 14.0 | 18.0 | 13.0 | 19.0 | 1.65 | 1.75 | 0.2 | 2.0 | 1.7 |
Ultra High Power | 250-500 | 5.8 | 4.5 | 14.0 | 18.0 | 14.0 | 20.0 | 1.68 | 1.77 | 0.2 | 1.5 | 1.4 |
4.Pictures of Graphite Electrodes
5. FAQ
We have organized several common questions for our clients,may help you sincerely:
①How about your Warranty of Graphite Electrodes with big Dia.?
Warranty: 1-Year for the whole light. Warranty is based on correct storage, installation, using and maintenanc
②How to guarantee the quality of the products Graphite Electrodes with big Dia.?
We have established the international advanced quality management system,every link from raw material to final product we have strict quality test;We resolutely put an end to unqualified products flowing into the market. At the same time, we will provide necessary follow-up service assurance. We have D&B report and you could check details information for our company.
③How long can we receive the product after purchase?
In the purchase of product within three working days, We will arrange the factory delivery as soon as possible.
- Q: Thermal expansion coefficient of graphite
- The graphite electrode in the thermal expansion coefficient is related with the diameter of the graphite electrode, you have what is the expansion coefficient of specific diameter range not to say it, I put the general heat on high power graphite electrode national Ministry of metallurgical industry YBT/4089--2000 give you a lower coefficient of expansion. For reference only
- Q: After electrolysis of CuCl2 solution with graphite electrode for a period of time, we can observe that the graphite surface attached to the DC power supply is attached to the red material,And will the color of the solution be deep or shallow?
- Negative poleThe color becomes lighter (the copper ion gets electrons in the cathode and becomes copper)
- Q: Will the brush grease not short-circuit the commutator?
- The reverse pole surface should be clean and dry. Any grease, moisture or dust will destroy the carbon film on the commutator surface. The carbon film can not be formed or destroyed. It is very harmful. Grease material will be embedded in the joint between commutator and commutator. Under the action of electric spark, it will be carbonized and conductive. When serious, it will cause partial short circuit between the reversing pieces and reduce the service life of reversing.
- Q: What are the losses in graphite electrode?
- In EDM, discharge principle is to remove the workpiece material by using the tool and the workpiece anode spark discharge explosion, spark discharge is bidirectional, not only will the workpiece removal part, forming processing, will cause some loss of electrode. Electrode loss is one of the main causes of machining errors in machining, and is an important technical parameter affecting the accuracy and quality of EDM
- Q: Iron and graphite as electrodes and Nacl as electrolyte solutions. Why do they produce electric current? Graphite and iron react not with solution, can they be connected by wires?
- Graphite here acts only as an electrode, and the real reaction on the graphite is oxygen, the galvanic cell reaction called iron oxygen corrosion
- Q: After vacuum melting of quartz crucible, there are three graphite electrode rods. What's the adjustment?
- Or did you adjust the electrode when it was installed? There are two electrode distance, two away, causing melting after different lengths.
- Q: How can I electroplate iron? I would like to use graphite as an electrode. Iron is plated on graphite with iron solution, so it can be processed into iron parts. I wonder if it can be done
- Iron plating can be, with 2 valence iron, but on the graphite joint force is good, it is difficult to say, electroplating is bad, peeling is also common. Relatively speaking, iron parts on nickel plating is relatively simple, also more applicable
- Q: Jiqiu conductive graphite electrode, how to compare with copper is relatively large resistance value?
- Look at what kind of graphite electrode you need. Now, the resistivity of ordinary power graphite electrode in our factory is 7.5-8.5. It is not clear that the graphite electrode is dipped in 6--7.3. copper
- Q: Excuse me, why does the graphite electrode flake when electrolyzed salt water is used?
- The structure of the electrolytic cell is different when the electrolytic cell is constructed with different electrolytes
- Q: Graphitized anode, cathode and graphite electrode, respectively How can one differentiate and use differently?
- In electrolysis industry, using graphite anode plate as the anode has a history of more than 100 years, the metal anode is in recent decades, the research and application of metal anode in China late last century, only in 70s the technology related to the research and experiment of metal anode, anode on electrolysis industry, mainly through the silver (2%) (0.5%): low silver lead silver alloy, lead and silver tin antimony alloy, lead calcium alloy and lead silver alloy adding nucleating agents and several stages
Send your message to us
Graphite Electrodes for Water Electrolysis - Big Dia. Super Quality
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 400 m.t.
- Supply Capability:
- 5000 m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords