Electro Galvanized Wire For Chain Link Fence

Chat Online

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Place of Origin:	Hebei China (Mainland)	HS Code:	721720000	Model Number:	Q195
Surface Treatment:	Galvanized	Galvanized Technique:	Hot Dipped Galvanized	Type:	Round Wire
Function:	Binding Wire	Wire Gauge:	5.0mm-0.5mm	Material:	Low carbon steel wire
Zinc coating:	>40g/m2	Tensile Strength:	350N-600N/mm2	Roll weight:	200gram-300kgs/roll
Packing:	plastic inside and woven bag cloth outside

Packaging Detail:	Packing:5kgs-25kgs/roll common,plastic inside and woven bag outside. In 20'ft can load 25tons.
Delivery Detail:	depends on amount

Hot dipped galvanised iron wire
Hot sell:0.8mm,0.71mm
Zinc coating:>40g
Soft,anti-corrossion
Type:binding wire,wire mesh etc

Hot Dipped Galvanized Iron Wire

Zinc Coating:>40g/m2

Feature:

Hot dipped galvanized wire has great flexibility, high zinc coated, corrosion resisting.

Application of Hot dipped galvanized wire:

Because of the thicker zinc coating, hotdipped galvanized wire has better protective properties, so it is used for harsh working environment,

and it is widely applied in chemical industry, oil processing, marine exploration, metal structure, power transmission, scaffold, bridge, etc.

Electro Galvanized Iron Wire

Zinc Coating:8g-12g/m2

Feature: Electro galvanized wire has great flexibility, through drawing and electric galvanizing,

as one of the binding wires, it is an ideal material for construction and industry.

Application: In weaving of wire mesh, fencing for expressway and construction,

and it also widely supplied in the form of coil wire, spool wire, cut wire, wire tie, binding wire, etc.

Q:I am replacing an old outlet with a GFCI and I have encountered a red wire...what is the red wire for?: It sounds like that receptacle was half switched. Receptacles are designed to have the small brass tab on the black side snap off and one half is constantly alive (black wire)and the other side is connected to a wall switch (red wire). Is this in a room with no ceiling light? Switched outlets are usually for a lamp to turn on as you enter the room. GFCI outlets are not designed to be switched on and off as both sides will go off. Is this room in a basement, kitchen, bathroom or near water pipes? You may not be required to have it GFCI protected. If you can and want a GFCI then try another outlet near by.

Q:In that chart it has 2 sections, one is maximum amps for chassis wiring and the other is maximum amps for power transmission. What is considered chassis wiring and what is considered power transmission?: Chassis wiring assumes each wire is routed separately, and power wiring assumes they are wired in a bundle. In chassis wiring the cooling of the conductors is better, because they are all exposed directly to air. In a bundle, some of the wires are not in direct contact withe the air.

Q:in hooking up a hot wire from the battery to a toggle switch inside a vehicle, i ran a seperate ground wire to the body, there are 2 wires coming from the unit i need to hook to the toggle switch.how do i test to see which one of those is a hot wire? i am not too smart at this. ty kindly: Depends on what your hooking up? Look at the unit where the wires go in and there may be a +(hot) or -(ground) marking, and the ground wire is usually black and the hot is usually red,orange or yellow.

Q:i need an egr wiring Diagram for a 2000 Chevy Malibu. the wires got pulled out of the weather tight connector. if anyone can help i'd appreciate: Connector view for the GM linear EGR valve are as follows: Pin# A=gray/w black wire,Pin# B=solid black wire,Pin# C=brown/w white wire,Pin# D=brown/w white wire(see note) and Pin# E=solid red wire! NOTE since pin C+D have the same color wire the correct wire must be identified by checking the voltage with the KOEO (key on engine off) the right brown/w white wire should have a 5volt reference voltage with the key on engine off! Hope this helps.

Q:I get how to solder one wire to the inverter, but how do I do multiple wires? Do I connect end-on-end, or all at the same source? I couldn't find a good website for doing multiple wires...: don't okorder /

Q:Any instructions on how to make rings, necklaces, and bracelets out of colored telephone wire.: We okorder /

Q:So I customized my guitar, and now I need to wire it. i have a pre-wired pickguard but I don't know how to actually hook it up. There's 3 wires. I have 2 humbuckers, 1 singlecoil, 1 tone, and 1 volume. All I know is that one wire gets soldered to the back where the springs are and another wire goes to the input jack. But there's a 3rd wire and I don't know where it goes. I don't even know which wire goes to what. Please don't post a diagram because it doesn't help. I think the wire colors are white, blue, and yellow. Please help!: OK...I okorder /... That should hook you up.

Q:Does lime wire add a lot of pop-ups and slow down your computer?: Yes it does. Those are called Malware, for malicious software. 1 in 9 downloaded files are malware, or have some type of virus in them, or are just a virus by themselves.

Q:subs - dvc 4ohm 2 of them 600wattrms on each wiring it to a 1200 watt amp same brand as sub amp is 1 ohm stable to i wire the subs together and then to the amp a 1ohm? that would give each sub 600 watts right?: no wat i would do is wire 1 speaker to 1 port and wire the other speaker to the other pot thats if it is a 2 chanel amp... cause if not u will be pulling to much from 1 side and the speakers wont sound right..... u need to turn down the amp to at first and then bring up the bass gradually to make sure the speakers can handle it..... u also have the choice to bride the amp but thats it the spakers can handle the power... all u have to do is hook up positive then negative to 1 speaker the hook up positive then negative to a diffrent speaker but it has to be from a diff channel...... but if ur going to bridge the speakers then u go positive from 1 port to the negative to the negative of the other port this will give u alot more power to ur speakers.... thats why i recomend u hooking them up regular at first........... u also have to make sure ur gornd is like a foot long or less.... the shorter the ground the more the bass

Q:i am looking for a wire diagram for a 03 eclipse gts with an infinity factory radio and built in amp. i was curios if you can add another amp and sub to this system to give it a little more bass: For the best answers, search on this site https://shorturl.im/avvlm hooking up stereos is hard, sometimes the cables dont even match colors, and you need a tester to see which is gain and which is ground.

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range