The pump is a centrifugal pump of horizontal,axial end suction and radial discharge design. This is a universal structure of chemical process pump used internationally.
- Q:Do you need to disassemble the chain for replacing the oil pump of TOYOTA corolla?
- Hello, timing chain is generally no need to disassemble, you need to remove the oil pan, the oil pump may also have a chain
- Q:How to judge the good and bad of automobile oil pump?
- Diagnostic computer to see if the oil pressure is normal, useful to praise, thank you.
- Q:Audi a6l2.0 engine oil pump timing, right?
- A little, see, simple
- Q:The oil pump is not working well. What about the engine?
- The oil pump is not working well and affects the lubrication effect of the car. It is several thousand revolutions per minute. The piston ring oil ring and cylinder wall friction, so long, not only prone to the engine temperature is too high, and may cause the wear of piston ring or the cylinder wall, if the result of wear is more trouble, there will be cylinderscoring phenomenon resulting in piston ring and the cylinder wall gap is too large, the oil into the cylinder, is what we say oil burning, automobile exhaust is not normal, a row of black smoke, causing the engine power shortage or repair as soon as possible.
- Q:Motorcycle not oil, oil pump work well, oil road is not blocked, how to check?
- Please ignore the task
- Q:What are the problems caused by engine oil pump damage?
- The damage to the diesel engine oil pump will cause the following problems and solutions:(1) the oil inlet and outlet pipe of the oil pump is leaking at the joint, the oil pump stops supplying oil, and the inlet and outlet pipe gaskets are replaced, and the sealing surface is tightly sealed.(2) oil pump, check valve and seat surface wear or damage, failure, the oil pump does not supply oil, grinding, check valve seat surface or replace the check valve.(3) the oil pump piston wear and seal failure, the oil pump to stop oil supply, replace the piston treatment.(4) the oil pump piston spring is broken, the oil pump fails, the piston pump oil function is stopped, the oil pump is not supplied, the piston is replaced and the piston is taken off.(5) the oil seal of the piston rod of the oil pump is damaged, which causes the diesel oil to enter the injection pump cam chamber, and makes the engine oil of the diesel engine bottom oil become thinner. At this point, the oil seal of the top rod should be replaced.
- Q:Polo 1.4 changed the oil pump without oil
- The oil circuit is blocked
- Q:In the 1 to 2 seconds when the vehicle is started, does the oil pump inject engine oil into the engine?
- Yes, the oil pump follows the crankshaft
- Q:Where is the oil pump installed?
- When installing the engine oil pump, after the engine is refitted. When installed, the first crank, the first cylinder piston at TDC position, then pump filled with oil (don't forget), the oil outlet groove direction of pump shaft installed electric drive shaft plug towards the pump, when the oil into the engine body, recesses in parallel with the axis of the crankshaft.Effect of lubricating oil pump system within pump: pump is the engine oil level to a certain pressure, forced to pressure parts of the engine on the surface of the movement. The structure of oil pump can be divided into two types: gear type and rotor type. Gear type oil pump is divided into internal gear type and external gear wheel type, generally referred to as gear pump.Used to increase the pressure of the oil and to ensure a certain amount of oil,Oil pumpForced to the surface friction of oil components. The internal combustion engine is widely used in gear and rotor pump. The gear type oil pump has the advantages of simple structure, easy processing, reliable work, long service life, high pressure oil pump, rotor pump rotor is widely used for complex shape by powder metallurgy pressing. This pump has the advantages of gear pump is the same however, the advantages of compact structure, small volume.
- Q:4Y engine oil pump, okay? Still lifting the engine?
- Hello, this oil pump is not very good, the replacement of the oil pan is not very good, it is more troublesome to dismantle.
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average