Axially Split Casing Double Suction Pump

Ref Price:
Loading Port:
Payment Terms:
TT or LC
Min Order Qty:
1 unit
Supply Capability:
1000 Sets Per Month unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Single stage horizontal double suction design, reduce the axial force. Spli case type design make the service easy. Do not need move the pipe system when change the inside parts. Heavy duty bearing design suitable for and application.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Accord 2 is timing, how about the oil pump?
Hello, there are also some of the pump, on a black spot after even a little bit. And two black spots, a black spot on the point on the crankshaft, the two point of the oil pump is point, how many chains count on both sides, there is several chains Zhang tensioner!
Q:How long will the oil pump lubricate the engine parts after the engine is started?
The oil pump is driven by the engine. As long as the engine is running, the oil is pumped to the parts that must be lubricated at once. The crankshaft splash lubrication is of course another matter
Q:What are the fuel pump inspection items for diesel generator sets?
The main inspection items are as follows:1, the outer rotor and pump casing pump clearance;2, the internal and external rotor meshing clearance;3, rotor and pump cover face clearance;4. Flatness of pump cover.[diesel generator unit oil pump inspection notice]1, check valve planes such as abrasion, sag, pitting phenomenon, application of grinding paste on the plate grinding, severe cases should be renewed.2. The surface of the one-way valve seat on the shell should be replaced when worn or not smooth.3, the top rod and the top sleeve wear seriously, so that the gap increases, the seal becomes worse, diesel leakage seriously, you need to replace with the shell, or choose the enlarged size of the top rod, but need to pass mutual research.4, the coarse strainer tubing joints within the core, and easy to be cottony sundries plug, effect of fuel supply, it should always pay attention to the clean fuel and remove the dirt on the filter core.5, the hand pump piston rubber ring damaged, should be replaced in good time. After the center of gravity of the oil pump is assembled, the moving parts of the piston, the ejector rod and the other parts of the oil pump are required to be in good motion during the whole journey, and no blocking and blocking are allowed. The hand pump should be light and flexible. Pay attention to the installation of the one-way valve spring. The check valve spring must be accurately embedded in the spring slot.
Q:No oil for automobile oil pump
First of all, are you sure it is the oil pump? Is it a diesel pump?!! The oil pump is a toothed Wendeng. Where can I find a chain?
Q:Is the oil pump of electric vehicle controlled by electronic or mechanical transmission?
The oil pump of an electric vehicle is a mechanical transmission, and belongs to the lubrication system. Fuel injection pump is also mechanical transmission, whether common rail, monomer pump or other systems, are mechanical transmission, control system is electronic control, including injection time, injection times, jet volume, etc..
Q:How do I see the motorcycle's oil pump is broken? Two red
Look at the smoke in the muffler knew no oil pump is not good.
Q:The carbon pump is blocked, the Walla fell, the total amount of money to clean the engine?
What's your car, please?
Q:Does the motorcycle oil pump break down and cause the engine oil to burn?
The pits are ready for oil, lubrication, and burning
Q:What about the balance shaft of the automobile engine oil pump? How much does it cost to fix?
Working hours one thousand, accessories count. If the balance shaft can be replaced, no heavy repair will be required.
Q:The car burning oil pump replacement must do
1, there are many reasons, but also models (steam, firewood) and so on.2, long-term use of poor quality oil, or viscosity grade unqualified engine oil and other internal wear too large.3, under normal circumstances, the engine will burn some of the oil from the cylinder block, piston and valve lubrication, consumption within the relevant provisions of the national standard range for normal (GB/T19055), and vice versa. The lowest scale car burning oil is often accompanied by smoke or in a maintenance period is lower than the oil gauge oil level.4, long time does not change oil or too long delay, not timely maintenance; piston and piston ring due to the use of long, normal wear, or abnormal wear and tear caused by the gap is too large.5, in addition, there are valve seals, crankcase forced ventilation, PCV valve damage, congestion, oil pump pressure, or its own failure can also be caused.There are many reasons why, as you describe the content is not detailed, the temporary analysis so far.
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.

1. Manufacturer Overview

Location Hunan,China
Year Established 2006
Annual Output Value US$5 Million - US$10 Million
Main Markets 59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Africa
2.00% Oceania
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Export Percentage 51% - 60%
No.of Employees in Trade Department 6-10 People
Language Spoken: English, Chinese
b)Factory Information  
Factory Size: Above 100,000 square meters
No. of Production Lines Above 10
Contract Manufacturing OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range High and/or Average