Mainly used in conveying low/high temperature, neutral,corrosive liquid. Mainly applicable to the industries of petroleum catalytic cracking, coal liquefaction and coal vaporization, synthetic fuel,electric slag plant conveyance, etc.
- Q:What's the reason for the engine oil pump ringing in the morning?
- It's the valve. It's just started in the morning. The oil hasn't come up. It'll be ready for a while
- Q:The oil pump is driven without a belt
- That should be sub models, and some rely on the chain, some directly crank pulley
- Q:6140 lathe oil pump, no fuel injection, what is the problem?
- The fuel pump is clogged,
- Q:How to judge the good and bad of automobile oil pump?
- Diagnostic computer to see if the oil pressure is normal, useful to praise, thank you.
- Q:From where on the car can you see that the oil pump is not oiled?
- Hello, not on the oil, then 1 valve sound than normal, 2, open the oil cap to see, 3, the best way is conditional removal of oil sensors, get off to see
- Q:The car oil pump is broken. What are the problems?
- If you lose the oil pressure, the alarm light will go on, and continue driving will cause fatal harm to the engine.Adjustment of oil pressureThe oil pump is classified by the steady discharge of the pump, which means that the maximum pressure must be limited by the relief valve. If the pressure relief valve is not used, the system pressure will rise to a dangerous level, which may cause the engine to be damaged.The oil pressure reducing valve is composed of a valve or a ball and a coil spring. The oil is sucked in the strainer and sent to the oil filter. When the fuel supply pressure increases with the engine speed, the pressure relief valve opens. At this point, the oil enters the inlet side by way of the bypass from the exit side to maintain the specified pressure. Since the stiffness of the spring used on the pressure reducing valve is very accurate, the maximum pressure of the oil pump can be guaranteed. If the stiffness of the spring increases, the oil pressure will increase. But the pump will not increase the amount of oil discharge.In addition, the following factors affect engine oil pressure:1. the speed of the oil pump, the oil pressure increases with the speed increase;2., the viscosity of oil, the greater the viscosity of oil, the higher the oil pressure;3. oil gap, bearing clearance will hinder the oil pump boost. When the bearings wear, it is difficult to form the appropriate pressure.
- Q:How do I see the motorcycle's oil pump is broken? Two red
- Hello, friend. First of all, tell you that the two stroke motorcycle does not have an oil pump. If it's a four stroke. In 70, 90100 of the three models you can put the screws on the cylinder head of the lower right to loosen the. Then start the locomotive. If there is oil to the outside, then that the normal oil pump. If not, check the oil pump wheel for wear first. Because the oil pump wheel wear, even if the oil pump is not bad. It doesn't work either. The three models are identical in structure. Their oil pumps and pump wheels are relatively easy to break. Another 125 models, men's and women's pedals. Men's words a screw is loosen cylinder head top, then start. Organic oil emits just normal. No oil smoke, also want to look at the screen is not blocked. The screws on the ladies pedal are the same as the 7090100
- Q:The oil pump light is on all the time
- It's the oil pressure indicator, not the oil pump indicator light.This indicator is used to show the pressure of the engine oil. Open the key door. When the vehicle starts to self check, the indicator light is on and off after starting. The indicator light is always on, indicating that the engine oil pressure is lower than the required standard, you need to repair.If it's on all the time, just see if the oil is enough. How about the oil pressure switch, the wiring harness and the plug?. If it is flashing at some point, the possibility of a problem with the oil pressure switch itself is greater.
- Q:Volkswagen Polo pump for heating lamp and light machine
- Sometimes the oil lamp is bright because the oil sensor plug is not working well and the wires are loose and sometimes light.
- Q:A single cylinder diesel engine oil indicator does not come up
- Spindle mounting is not accurate, or the main bearing cover on the location of the crushing of the Ding, so that the spindle displacement caused by.
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average