Edco Roofing

Hot Products

Acoustic Perforated Decorative Panel, gypsum board, mgo board

Cheap Price Gypsum Board with Standard Size Factory

Gypsum Board Good quality Low Price Acoustic Perforated

Gypsum Board/ Drywall/ Plasterboard / Interior Wall Panel

Gypsum Board The Standard For Wall Partition

Moistureproof fireproof wave decorative gypsum board

Gypsum Board Cheap Roofing Material Fireproof Exterior Wall Panels

Gypsum Board/ Drywall/ Plasterboard/ Interior Wall Panel/ Paperbacked Plasterboard

Decorative standard size Gypsum drywall paper board

Gypsum Board Good Quality ,Low Price Acoustic Perforated

FAQ

Which glue is suitable for sticky gypsum board, for a long time.

Is the ceiling a gypsum board ceiling? Sand with the sand to polish the exposed gypsum board, clean the dust, and then glue the glass glue

Gypsum board wall batch of gray do not brush latex paint can be directly posted wallpaper?

Wallpaper paste up the requirements as long as the wall is flat, no moisture, no water, the structure can be stable. Gypsum board wall after the grant of ash, fully meet the requirements of the wallpaper. Unless the quality of ash is really unsatisfactory, rough, flatness can not meet the needs of stickers. Even so, you can then brush the putty again (the original layer only brush the next time under the premise), or the original wall all eradicated, re-do putty wall, and then posted wallpaper.

Gypsum board inside the keel with what method can be found?

(1) The vertical spacing between the keel is about 400mm, and the distance from the nearest side of the load-bearing wall can be calculated from the distance of 400mm and the width of the side of the 50mm light steel keel (that is, 450mm) The nearest place can be used to detect the specific position of the keel through the gypsum board with a small nail. (2) There is also because the gypsum wall in the keel are generally used light steel keel, so you can use the magnetic magnet to find the location of the keel.

I installed the lights on the gypsum board on the screw, not the kind of embedded lights

Installed relatively light, pull a few support lines on the lamp lock on the screw, expand the force point, you can achieve beautiful and practical function

Gypsum board on how to get rid of smoke

Penetration into the gypsum board inside the oil stains, has a strong penetration. The general coating can not cover it - re-do the coating layer, will be yellow in a few hours later, discoloration.

Will the brick wall and beam column cracks, cracks between the board, gypsum board cracks how to deal with

You describe these cracks, are fundamentally by the different materials in the temperature, humidity under the influence of physical changes, and now solve these problems are late with a ductile material remediation, like the wall and the ceiling of the corners of the case , To do that is the above method.

Home decoration ceiling with waterproof gypsum board or fire gypsum board is good

Bathroom with waterproof gypsum board plus anti-mildew paint, other parts with ordinary gypsum board can be. Rich words, with a higher strength of the fire board, because the internal addition of glass fiber, increased the strength and fire resistance, but the family is not significant.

Gypsum board used in the expansion agent

Prepared by anionic surfactants and foam stabilizer, diluted with water several times with a blowing agent into a rich and delicate foam, and gypsum paste made of gypsum board. ?????? Sodium dodecyl sulfate (K12), fatty alcohol polyoxyethylene ether sulfate (AES), sodium α-alkenyl sulfonate and other anionic surfactants can be used as a paper gypsum board Blowing agent. This kind of foaming agent has high foaming factor and low cost. But the foam stability is poor, usually with the use of foam stabilizer. At present, the main component of gypsum board foaming agent is still sodium dodecyl sulfate (K12), which is divided into solid product (above 93) and liquid product (30% aqueous solution).