Aluminum Copper Coil

Hot Products

Galvanized Steel Wire Steel Wire Galvanized Steel Strand Wire

PVC Coated Galvanise Black Annealed Double Loop Tie Wire

Galvanized Iron Wire In Coil With High Quality

Black Annealed Iron Binding Wire for Construction

Double Loop Tie Wire From China Supplier High Quality

Tie Wire Bending Wire and Cut Wire in Stock

Electric Galvanized Wire Hot Sale High Quality

Galvanized Iron Wire Galvanized Double Loop Tie Wire

Soft Tie Wire Black Annealed Iron Wire China Supplier

Carbon Steel Wire Rod

FAQ

like lets i want to want to connect my speaker wires with other wires can i use elmer glue so that it sticks and will the wires still work?

You could always solder it, but no, glue won't allow electricity to pass through.

I just installed a backup camera however I am having trouble wiring it. I've read that I need to tap into the reverse wire, however I went through many wires and couldn't figure out which one is it. My cameras wire is designed to be wired in the trunk, so the wire under the hood or dash is not a possibility. 2003 G35 Sedan

You can remove your tail light and tap into the reverse wire there. It is easy to find just look at your reverse light bulb and use a multimeter to test for positive and negative (that would be the right way to do it at least). If your wanting to have the camera able to be on all the time and viewed from the headunit then you would need to wire the camera to switched accessory so it has power when the car is on and hook up your head units wiring (which you will need to do anyway to make the h/u switch to b/u cam when you go into reverse) to the reverse wire.

Looking for legit (good) speaker wire?or does it depend? are all speaker wire good?the speaker wires are for car audio

the thicker or lower the number the better electrical transfer. 16-20 gauge is ok for close speaker mounting, 12-14 gauge is better etc. if running a high output system go with lower numbers.

How can u do a wire transfer? Is there anything extra that is needed to do this? Are you able to make a wire transfer from your home computer?

A wire transfer is done thru your bank and unless you have it already set up or a bank officer that you work with, you will have to probably go to the bank and sign off on the wire transfer. Other than that, if you have someone who will work with you at your bank, they may fax the needed paperwork to you and accept a fax back. You will need your banks routing number and your account number. Good Luck!

u said when i buy a jvc wiring harness one end plugs in the back of cd player and the wires coming out of that connect to the wires in car will they be the same color though? right now there is a harness already on the cd player and the wires are on it and they are pretty long i thought i just wire those wires from it to the ones in car but they diff. colors

wait wait . u must buy the wiring harness that correspond to ur car first. than u wud simply wire the new wiring harness u bought to ur deck and simply match the colors. and than u simply connect it to ur existing car harness. baaamm done .

how do I wire the generator so it can spin 360 on the pole with out snapping the wires.... Thanks

You need some ring contacts and brushes that will be touching those rings that will be spinning while the generator does to complete a circuit without twisting wires. Make sure you get the right size rings and wire for the amount of current

When was the hot-wire anemometer invented? and who was it?

Who Invented Anemometer

There are two switches – the left is for the fan, the right is for the light. They operate independently. I want to replace the light switch with one that has a motion sensor.There are four sets of bundled wires coming out of the back of the box. Each bundle has a white, a black, and a copper wire.Two black wires come out of each switch. The top wires go into two of the bundles in the back of the box, the bottom wires are connected with each other and with two more black wires coming out of the other two bundles coming out of the back of the box.All the white wires are twisted together with a red cap. All of the copper wires are twisted together with another red cap.My motion sensor has a red, black, green and yellow wire. The directions say the yellow wire is not used, because this is not a 3-way light. Is there a straightforward way to do this?

Sure is!. You wire it exactly the way the instructions say to. Which is to use the 2 wires on the existing switch. The bare wire on the switch (if present) is the ground and goes to the green. Just like the instructions say. You are apparently letting all those other wires scare you. The motion sensor is nothing more than an automatic switch. It does the same thing the existing switch does, using the exact same wires. Do Not touch any of the existing splices. Look again at the instructions. Take a deep breath and have at. I've been in control cabinets with Hundreds of wires in them. I ignored all but the ones I need to work on. Other wise I would still be there trying to figure it out! (chuckle)