Steel Union Nozzle

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
3000 Pieces pc
Supply Capability:
25000 Pieces per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

 

our garden  has followings feature

 

1)High smoothness

 

2) Very slow size error

 

3) Higher warranty

 

4) double ferule sturcture makes products' sealing function better

 

Material

 

C3600 or  C 3700, 3771

 

ISO certificated and raw material test available

 

Lead Time

 

small orders(below 8000PCS) will be finished within 20days

 

Larger order will be sure accord our aggrement.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Hydraulic tubing connections are made of material steel
Such as carbon steel and cast iron, a much more used, less material costsBut if you're under a lot of pressure, try using carbon steel
Q:What does the pipe connector type "10-R1/4" mean?
The through and inside connections also refer to the nylon tube inserted as the 10mm tube.
Q:Can flared and jacketed hydraulic couplings be used as gas line couplings?
The pressure of the pneumatic pipeline is usually 0.8MPa.Yes, the life is longer than the pneumatic one
Q:Press the hydraulic pipe fittings standard need to do what procedures
The corresponding micrometer scale is 3. Installed with 33mm mold on the mold seat, and rotated to 3 micrometer scale, the hose peeling and joint assembly. After measuring the joint outer diameter of buckling is buckling parameter table after withholding value 33.5mm is withheld. If the diameter does not conform to withhold, after a fine micrometer withhold hose. Withhold hose connector: swage size too much, hose layer broken, causing leakage; too little buckling size, and hydraulic oil spill caused by rushing out of joint.
Q:What are the types of tubing and pipe couplings applicable to each occasion?
According to connection tubing and pipe joints, pipe joints are welded, sleeve type, expanding type, press type form; pipe joints each form, according to the channel number and direction of joint points straight, rectangular, three other types; threaded connection and flange connection with the connection of the body. In addition, there are some special purpose pipe couplings.
Q:Why are the sleeve joint leaks?
The hardness of the clamping edge is not enough, or the steel pipe is too hard. After the assembly, the clamping edge can not cut into the pipe wall to form a seal. Solve: replace the qualified card sleeve.The end face of the steel pipe is not vertical or clean, which hinders the proper installation of the pipe. Solution: carefully clean the end face before installation.The joint body and the steel with different axis, leading to the assembly is not correct, extrusion is not tight, at this time can be found in the card set apart and cut the pipe wall, left the marks of a single whole foot ring groove. Solution: when installing, make sure the joint is coaxial with the steel symbol.
Q:110 degree PVC pipe joint
PVC pipe (PVC-U pipe) rigid PVC pipe is made of PVC resin and stabilizer, lubricant and so on. It is extruded and formed by hot pressing method. It is the earliest plastic pipe to be developed and applied. PVC-U pipes are corrosion resistant, easy to adhere, low in price and hard in texture, but because of the exudation of PVC-U monomers and additives, they are only suitable for the feed water system with a temperature of not more than 45 DEG C. Plastic pipes are used to transport potable water, waste water, chemicals, heating and cooling fluids, foodstuffs, ultrapure liquids, slurries, gases, compressed air, and vacuum systems.
Q:What are the standard drawing numbers for hydraulic couplings?
The ends of the pipe shall be flush. The pipe should be flush in sawing grinding wheel and other tools, and burr cleaning and blowing with high pressure air before use.When installing, the coaxiality of pipe and joint body should be kept as far as possible. If the pipe deflection is too large, it will cause sealing failure.If the pre loading force is unfavorable, the inner edge of the ambassador card sleeve is just inserted into the outer wall of the pipe, and the clamping sleeve should not be deformed obviously. When the pipeline connection, and then according to the specified tightening force assembly. Phi 6-1 card sleeve tightening force is 64-1 15N, 16 MMR 259n, Phi Phi 18mm for 450n. If the sleeve is badly deformed at pre assembly, it will lose its sealing effect.
Q:The difference between threaded pipe joint and grooved pipe joint
The wire connection and screw connection pipeline engineering: the form of thread docking between two pipes, valves, pipes and valves are connected or.
Q:How many bonding methods are there in the belt joint?
3. heat curing joint, the heat vulcanizing joint conveyor belt interface is completely closed, not susceptible to water wetting. Technology of belt vulcanizing joint is generally placed on the belt vulcanizer frame under the frame, both ends of the alignment, then put on the pressure plate, small thermal insulation board, insulation sheets, two vulcanizer installed on each side of 1-2 meters of the platform and fixed platform, the upper surface to the lower heating plate and flat surface homogeneous or slightly lower, also cannot affect the tension rod, the belt joint two on the platform began to cure. This method is a kind of joint is the best method that can guarantee the high coupling efficiency, but also very stable, joint life is long, easy to master, but the heat curing joint process is relatively complex, high requirements for personnel, cold bonding process is simple and short-term training posts.
We insist on the business philosophy of "quality standard coexists with the enterprise and market and honor be first", and sell products to relevant overseas companies. We have received honors given by our customers at home and abroad.We are looking forward to your visit and the pleasure to process according to your samples and drawings.

1. Manufacturer Overview

Location Zhejiang, China (Mainland)
Year Established 2008
Annual Output Value US$5 Million - US$10 Million
Main Markets North America
South America
Eastern Europe
Southeast Asia
Mid East
Western Europe
Northern Europe
Company Certifications Quality Management System Certification

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage 31% - 40%
No.of Employees in Trade Department
Language Spoken: English, Chinese, Spanish, Japanese, German, Arabic, French, Russian, Korean, Italian
b)Factory Information  
Factory Size: 5,000-10,000 square meters
No. of Production Lines 6
Contract Manufacturing OEM Service Offered Buyer Label Offered
Product Price Range Average