Stainless Steel Submersible Pumps
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Production Introduction:
This model of pump is vastly used for aquariums, mine enterprises, gardens, family spray and irrigation, watering flowerand flush. It is characterized with compact sizes, light weight and convenient use. The float switch can automatically control on and off without people’s supervision. It is also equipped with 1-phase capacitance-operation asynchronism motor.or 3-phase asynchronism motor, the protector in which can automatically cut off the power when it overheat or overcurrent, thus guarantee the security and reliability of pump’s operation even in the atrocious environment.
Function and feature:
Model QDX(P) Stainless steel casing submersible pump is vastly used for aquariums, mine enterprises, gardens, family spray and irrigation, watering flower and flush. It is characterized with compact sizes, light weight and conbenient use. The float switch can automatically control on and off with the chage of water level. It is also equipped with 1-phase capacitance-operation asynchronism motor, or 3-phase asynchronism motor, the protector in which can automatically cut off the power when it overheated or overcurrented, thus guarantee the security and reliability of pump’s operation even in the atrocious environment.
Condition of usage:
1.The depth of the electrical pump below the water is no more than 5m;
2.The temperature of the water is no higher of 40*C ;
3.The PH figure of the water is between 6.5-8.5;
4.The grain diameter of the solids in the water is no bigger than 0.2mm;
- Q: What is the difference between swashplate pump and crankshaft pump?
- Piston pump: valve plate, valve plate, piston, piston ring, crankshaft, connecting rod and so on, all belong to its spare parts.Piston pump working principle: by the piston in the pump cylinder for reciprocating movement to suction and remove liquid.
- Q: Fire pump and shower pump flow head selection, high resolution.
- 2, the volume is greater than 10000 is less than 25000, the minimum water consumption of indoor fire hydrant is 15L/s
- Q: How can the submersible pump level meter be connected?
- Install liquid level controller, two position liquid level sensor, controller to buy manual, wiring according to wiring diagram.
- Q: What is a solution pump?
- 2.1 advantages of canned pumps(1) fully enclosed. There is no dynamic seal in the structure. Only the static seal in the outer shell of the pump can be made without leakage. It is especially suitable for transporting flammable, explosive, precious liquids and toxic, corrosive and radioactive liquids(2) high safety. The rotor and stator each have a shielding sleeve, so that the rotor and stator of the motor are not in contact with the material, even if the shield is broken, it will not produce the risk of leakage and leakage(3) compact structure and small footprint, the pump and motor is a whole, disassembly and assembly do not need to find the center. The base and foundation requirements are low, and the daily maintenance workload is low, and the maintenance cost is low
- Q: What are the starting and stopping procedures for centrifugal pumps?
- The use of centrifugal pump can be divided into three steps, namely, start, run, stop.Start: you should do the following preparation before starting:(1) check the water pump equipment in good condition.(2) the bearings are filled with oil, the oil level is normal, and the oil quality is qualified(3) all the inlet valves of the centrifugal pump are opened.(4) pump water injection or vacuum pump diversion (except for flow), open the vent valve exhaust.(5) check the leakage of shaft seal. It is advisable to fill the seal with a little drop of water.(6) the motor rotates in the right direction.
- Q: What is the displacement of the pump? Flow? What is the volume efficiency and mechanical efficiency of the pump?
- Displacement of a pump: the volume of the discharged liquid calculated by the change in the size of the sealing geometry for each revolution of the hydraulic pump
- Q: What is the difference between centrifugal pump and positive displacement pump?
- Positive displacement pump is the volume pump, this type of pump is to rely on changes in volume to compress fluid work, including: diaphragm pumps, gear pumps, screw pumps, etc.;
- Q: What are the parts of a pump? How do you classify it?I just want to know
- According to the working principle can be divided into: centrifugal type and volume type centrifugal pump. By the centrifugal force of the impeller will accelerate the refrigerant, through to stay, so as to achieve the purpose of boosting; volume by changing the refrigerant in the flow volume to boost purpose.According to the media and installation conditions, water pump: centrifugal pump used: the impeller pump shaft, a curved blade on the impeller impeller outlet. The central entrance water vertically along the tangential direction of axial flow pump: high speed, large flow, low lift, mixed flow pump and centrifugal pump structure similar to that of the blade outlet angle is different, wide flow channel, close to the performance of axial flow pump displacement pump: safety valve must be opened before the start (metering pump, screw pump)
- Q: How many concrete pump tube diameter
- Different pipe diameter is different, most of the 125, there are 150. Now we have the smallest pump on the market, with a pipe diameter of 100.
- Q: Does the control cabinet of the fire control pump need to be related to the fire control room?
- Normal words are needed, but when you check and check, has anyone checked?
Send your message to us
Stainless Steel Submersible Pumps
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords